The Company administrator has issue the "show vlan id 5" command.
What will this command display? ()
A. Ports in VLAN 5
B. Utilization
C. VLAN information on port 0/5
D. Filters
E. MTU and type
您可能感興趣的試卷
你可能感興趣的試題
Which of the following should you enable to prevent a switch from forwarding packets with source addresses that are outside an administratively defined group? ()
A. DAI
B. STP
C. PVLAN
D. port security
Refer to the exhibit. The switchport output in Figure 1 displays the default settings of interface FastEthernet 0/13 on switch SW1. Figure 2 displays the desired interface settings.
Which command sequence would configure interface FastEthernet 0/13 as displayed in Figure 2? ()
A. SW1(config-if)# switchport trunk encapsulation dot1q SW1(config-if)# switchport mode trunk SW1(config-if)# switchport trunk native DATA SW1(config-if)# switchport trunk allowed vlan 1,10,20
B. SW1(config-if)# switchport trunk encapsulation dot1q SW1(config-if)# switchport mode dynamic auto SW1(config-if)# switchport trunk native DATA SW1(config-if)# witchport trunk allowed vlan add 1,10,20
C. SW1(config-if)# switchport trunk encapsulation dot1q SW1(config-if)# switchport mode dynamic desirable SW1(config-if)# switchport trunk native vlan DATA SW1(config-if)# switchport trunk allowed vlan 1,10,20
D. SW1(config-if)# switchport trunk encapsulation dot1q SW1(config-if)# switchport mode dynamic desirable SW1(config-if)# switchport trunk native vlan 10 SW1(config-if)# switchport trunk allowed vlan 1,10,20
E. SW1(config-if)# switchport trunk encapsulation dot1q SW1(config-if)# switchport mode dynamic Desirable SW1(config-if)# switchport trunk native vlan 10
You need make configuration changes to an existing layer 3 switch in the Company network. On a multilayer Catalyst switch,
which interface command is used to convert a Layer 3 interface to a Layer 2 interface?()
A. switchport access vlan vlan-id
B. switchport
C. switchport mode access
D. no switchport
E. None of the other alternatives apply
Refer to the exhibit. The user who is connected to interface FastEthernet 0/1 is on VLAN 10 and cannot access network resources. On the basis of the information in the exhibit,
which command sequence would correct the problem?()
A. SW1(config)# vlan 10SW1(config-vlan)# no shut
B. SW1(config)# interface fastethernet 0/1SW1(config-if)# switchport mode accessSW1(config-if)# switchport access vlan 10
C. SW1(config)# interface fastethernet 0/1SW1(config-if)# switchport mode access
D. SW1(config)# vlan 10SW1(config-vlan)# state active
E. SW1(config)# interface fastethernet 0/1SW1(config-if)# no shut
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them.
What will be the result?()
A. IEEE 802.1D and IEEE 802.1w are incompatible. All three switches must use the same standard or no traffic will pass between any of the switches.
B. Switches S1, S2, and S3 will be able to pass traffic between themselves.
C. Switches S1, S2, and S3 will be able to pass traffic between themselves. However, if there is a topology change, Switch S2 will not receive notification of the change.
D. Switches S1 and S3 will be able to exchange traffic but neither will be able to exchange traffic with Switch S2
最新試題
Based on the show spanning-tree vlan 200 output shown in the exhibit, which two statements about the STP process for VLAN 200 are true? ()
Which two statements are true when the extended system ID feature is enabled? ()
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result?()
What two things will occur when an edge port receives a BPDU?()
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command, which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true?()
Which two statements about the various implementations of STP are true?()
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain, the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change?()
What must be the same to make multiple switches part of the same Multiple Spanning Tree (MST)?()
During routine maintenance, G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However, after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ? ()
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network, Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit, which two statements are true?()