Based on the show spanning-tree vlan 200 output shown in the exhibit，
which two statements about the STP process for VLAN 200 are true？ （）
A.BPDUs will be sent out every two seconds.
B.The time spent in the listening state will be 30 seconds.
C.The time spent in the learning state will be 15 seconds.
D.The maximum length of time that the BPDU information will be saved is 30 seconds.
E.This switch is the root bridge for VLAN 200.
F.BPDUs will be sent out every 10 seconds.
您可能感興趣的試卷
你可能感興趣的試題
A.HSRP
B.GLBP
C.VRRP
D.SLB
E.RPR
F.RPR+
A.STP timers values （hello， forward delay， max age） are included in each BPDU.
B.A switch is not concerned about its local configuration of the STP timers values. It will only consider the value of the STP timers contained in the BPDU it is receiving.
C.To successfully exchange BPDUs between two switches， their STP timers value （hello， forward delay， max age） must be the same.
D.If any STP timer value （hello， forward delay， max age） needs to be changed， it should at least be changed on the root bridge and backup root bridge.
E.On a switched network with a small network diameter， the STP hello timer can be tuned to a lower value to decrease the load on the switch CPU.
F.The root bridge passes the timer information in BPDUs to all routers in the Layer 3 configuration.
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.
Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
A.DSW11（config）# spanning-tree vlan 1 priority 4096
B.DSW12（config）# set spanning-tree priority 4096
C.ASW13（config）# spanning-tree vlan 1 priority 4096
D.DSW11（config）# set spanning-tree priority 4096
E.DSW12（config）# spanning-tree vlan 1 priority 4096
F.ASW13（config）# set spanning-tree priority 4096
Given the above diagram and assuming that STP is enabled on all switch devices，
which two statements are true？（）
A.DSW11 will be elected the root bridge.
B.DSW12 will be elected the root bridge.
C.ASW13 will be elected the root bridge.
D.P3/1 will be elected the nondesignated port.
E.P2/2 will be elected the nondesignated port.
F.P3/2 will be elected the nondesignated port.
A.Upon bootup，a port transitions from blocking to forwarding because it assumes itself as root.
B.Upon bootup，a port transitions from blocking to listening because it assumes itself as root.
C.Upon bootup，a port transitions from listening to forwarding because it assumes itself as root.
D.If a forwarding port receives no BPDUs by the max_age time limit， it will transition to listening.
E.If a forwarding port receives an inferior BPDU， it will transition to listening.
F.If a blocked port receives no BPDUs by the max_age time limit， it will transition to listening.
最新試題
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
Which three statements about STP timers are true？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）