Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them.
What will be the result？（）
A. IEEE 802.1D and IEEE 802.1w are incompatible. All three switches must use the same standard or no traffic will pass between any of the switches.
B. Switches S1， S2， and S3 will be able to pass traffic between themselves.
C. Switches S1， S2， and S3 will be able to pass traffic between themselves. However， if there is a topology change， Switch S2 will not receive notification of the change.
D. Switches S1 and S3 will be able to exchange traffic but neither will be able to exchange traffic with Switch S2
您可能感興趣的試卷
你可能感興趣的試題
The network administrator maps VLAN 10 through 20 to MST instance 2.
How will this information be propagated to all appropriate switches？（）
A. Information will be carried in the RSTP BPDUs.
B. It will be propagated in VTP updates.
C. Information stored in the Forwarding Information Base and the switch will reply on query.
D. Multiple Spanning Tree must be manually configured on the appropriate switches.
Refer to the show spanning-tree mst configuration output shown in the exhibit.
What should be changed in the configuration of the switch SW_2 in order for it to participate in the same MST region？ （）
A. Switch SW_2 must be configured with an instance number of 2.
B. Switch SW_2 must be configured with a different VLAN range.
C. Switch SW_2 must be configured with the revision number of 1.
D. Switch SW_2 must be configured with a different MST name.
While logged into a Company switch you issue the following command：
CompanySwitch（config-mst）# instance 10 vlan 11-12
What does this command accomplish？（）
A. It enables a PVST+ instance of 10 for vlan 11 and vlan 12
B. It enables vlan 11 and vlan 12 to be part of the MST region 10
C. It maps vlan 11 and vlan 12 to the MST instance of 10.
D. It creates an Internal Spanning Tree （IST） instance of 10 for vlan 11 and vlan 12
E. It create a Common Spanning Tree （CST） instance of 10 for vlan 11 and vlan 12
F. It starts two instances of MST， one instance for vlan 11 and another instance for vlan 12.
Which MST configuration statement is correct？ （）
A. MST configurations can be propagated to other switches using VTP.
B. After MST is configured on a Switch， PVST+ operations will also be enabled by default.
C. MST configurations must be manually configured on each switch within the MST region.
D. MST configurations only need to be manually configured on the Root Bridge.
E. MST configurations are entered using the VLAN Database mode on Cisco Catalyst switches.
A. MST00
B. MST01
C. the last MST instance configured
D. none
最新試題
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
Which two statements about the various implementations of STP are true？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
What two things will occur when an edge port receives a BPDU？（）
Which statement is correct about RSTP port roles？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）