A. MST00
B. MST01
C. the last MST instance configured
D. none
您可能感興趣的試卷
你可能感興趣的試題
A. Region name
B. Configuration revision number
C. VLAN instance map
D. IST STP BPDU hello timer
E. CST instance map
F. PVST+ instance map
Which of the following specification will allow you to： associate VLAN groups to STP instances so you can provide multiple forwarding paths for data traffic and enable load balancing？ （）
A. IEEE 802.1d （STP）
B. IEEE 802.1s （MST）
C. IEEE 802.1Q （CST）
D. IEEE 802.1w （RSTP）
Which of the following specifications is a companion to the IEEE 802.1w Rapid Spanning Tree Protocol （RSTP） algorithm， and warrants the use multiple spanning-trees？ （）
A. IEEE 802.1s （MST）
B. IEEE 802.1Q （CST）
C. Cisco PVST+
D. IEEE 802.1d （STP）
E. None of the other alternatives apply
pany uses MSTP within their switched LAN.
What is the main purpose of Multiple Instance Spanning Tree Protocol （MSTP）？（）
A. To enhance Spanning Tree troubleshooting on multilayer switches
B. To reduce the total number of spanning tree instances necessary for a particular topology
C. To provide faster convergence when topology changes occur in a switched network
D. To provide protection for STP when a link is unidirectional and BPDUs are being sent but not received
E. None of the other alternatives apply
The Company network utilizes the Multiple-instance Spanning Tree protocol in its switched LAN.
Which three statements about the MST protocol （IEEE 802.1S） are true？ （）
A. To verify the MST configuration， the show pending command can be used in MST configuration mode.
B. When RSTP and MSTP are configured； UplinkFast and BackboneFast must also be enabled.
C. All switches in the same MST region must have the same VLAN-to-instance mapping， but different configuration revision numbers.
D. All switches in an MST region， except distribution layer switches， should have their priority lowered from the default value 32768.
E. An MST region is a group of MST switches that appear as a single virtual bridge to adjacent CST and MST regions.
F. Enabling MST with the "spanning-tree modemst" global configuration command also enables RSTP.
最新試題
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）