A.3 messages
B.6 messages
C.4 messages
D.2 messages
E.5 messages
您可能感興趣的試卷
你可能感興趣的試題
A.Incorrect VPI and VCI configuration
B.Noise, gain hits, or other transmission problems on the data link equipment
C.ATM cells are dropped due to incorrect ATM routing in the service provider.
D.A faulty or failing ATM interface.
E.Cells are dropped due to traffic policing in the ATM cloud on one or more virtual circuits attached to theATM interface
A.CBWFQ
B.CB-WRED
C.LLQ
D.Custom Queueing
E.WRR Queueing
A.VLAN Trunk Protocol (VTP)
B.State Synchronization Protocol (SSP)
C.L2VPN
D.Ethernet Virtual Switch Interface (VSI)
E.Label Distribution Protocol (LDP)
A.9 LCCs
B.7 LCCs
C.10 LCCs
D.6 LCCs
E.8 LCCs
A.multipart-to-multipoint EVC (E-LAN)
B.hub spoke EVC (E-Tree)
C.point to point EVC (E-Line)
D.rooted multipoint EVC (E-Tree)
E.point-to-multipoint EVC (E-Tree)
A.MPLS TE supports admission control
B.MPLS TE tunnel traffic is a link attribute to compute the TE tunnel path
C.MPLS TE uses BGP extension to advertise link attributes
D.MPLS TE provides protection capability
E.MPLS TE uses RSVP to establish LSP
A.Allows the transportation of all forms of traffic
B.Multiplexing is easy
C.Clocks do not need to be synchronized
D.Reduces network complexity and cost
E.Padding is not necessary and not permitted
A.It is mainly used in Intra-AS MPLS VPLS deployments and is configured at the ASBR to avoid misconfiguration of the Route Target assignment for VPN configurations
B.It is mainly used in Inter-AS MPLS VPN deployments and is configured at the ASBR to avoid misconfiguration of the Route Target assignment for VPN configurations
C.It is mainly used in Intra-AS MPLS VPLS deployments and is configured at the Router Reflectorto avoid misconfiguration in Route Target assignment for VPN configurations
D.It is mainly used in Inter-AS MPLS VPLS deployments and is configured at the Router Reflectorto avoid misconfiguration of the Route Target assignment for VPN configurations
E.It is mainly used in Inter-AS MPLS VPLS deployments and is configured at the PE router to avoid to misconfiguration of the Route Target assignment for VPN configurations
A.Routing information received through an IBGP session is not forwarded to another IBGP neighbor, onlyto EBGP neighbors
B.Routing information received through an EBGP session is not forwarded to another EBGP neighbor,only to IBGP neighbors
C.BGP neighbor peerings are established and sychronized using the TCP 3-way handshake
D.BGP shall not advertise a route until that route has been learned via an IGP also
A.10 Gigabit Ethernet does not support VLAN definition
B.10 Gigabit Ethernet supports full duplex links, but does not support half duplex links
C.10 Gigabit Ethernet supports unshielded or shielded twisted-pair cable connections
D.10 Gigabit Ethernet supports Carrier Sense Multiple Access with Collision Detection (CSMA/CD)
E.10 Gigabit Ethernet supports optical fiber connections in single mode only. Mufti mode is not supported
最新試題
Which two statements about Layer 3 MPLS VPN are true?()
Which option is not a valid method to assign the lowest-order 64-bit field of an IPv6 unicast address?()
What layer of the TMN (telecommunications management network) model does CTM fit into?()
Which two routers support cable access?()
Which statement about implementing the Cisco IPv6 provider Edge Router over MPLS is true?()
How many messages does internet Key Exchange use to negotiate SA characteristics when running inmain mode?()
Which four statements about Ethernet virtual circuit (EVC) infrastructure are true? ()
Which two statements about 10 Gigabit Ethernet (10GE) are true?()
In the Carrier Supporting Carrier (CsC) feature, which two protocols run between CSC-PE and CSC-CE().
What are three common reasons for ATM CRC errors?()