A. admin， operator， network-admin， and network-operator
B. admin， read-only， network-admin， and network-operator
C. vdc-admin， vdc-operator， network-admin， and network-operator
D. vdc-admin， vdc-operator， network-admin， and network-operator （for Nexus 7000） and network- admin and network-operator （for other Nexus switches）
E. admin and read-only
您可能感興趣的試卷
你可能感興趣的試題
A. IGMP is not synchronized between vPC peers
B. Cisco Fabric Service carries IGMP entries across the vPC peer link
C. IP ARP synchronization under the vPC domain configuration also synchronizes IGMP
D. IGMP is flooded to the L2 domain， and there is no need to synchronize it between vPC peers
A. The OTV control-plane protocol uses the IS-IS protocol to establish adjacencies and exchange MAC reachability across the overlay network. You must enable IS-IS with the feature isis command before OTV adjacencies can be established.
B. OTV uses an SSM group range for neighbor discovery and to exchange MAC reachability with other OTV edge peers.
C. The OTV join interface is a routed uplink interface on the edge device used to physically join the overlay network.
D. The OTV internal interface encapsulates the site Layer 2 frames in IP unicast or multicast packets that are then sent to the other sites.
A. C84C·75FA·6000
B. 01005·E11.·2FD
C. C84C·76FA·6000
D. 4000.0000.0001
A.The following XML-based NETCONF operations are supported in NX-OS SoftwarE˙close-session copy-config delete-config and edit-config
B.The following XML-based NETCONF operations are supported in NX-OS SoftwarE˙close-session copy-config edit-config and kill-session
C.NX-OS Software supports up to a maximum of 16 concurrent XML sessions
D.Only show commands are supported via the XML management interface in NX-OS Software
E.The NX-OS implementation of the XML-based NETCONF requires SSH to be used for communication with the device
A. In a vPC topology， the primary HSRP router will respond to ARP requests， but both HSRP routers will forward data traffic. No additional configuration is required.
B. In a vPC topology， the primary HSRP router will respond to ARP requests， but both HSRP routers will forward data traffic if the peer-gateway feature is enabled.
C. You can configure two overlapping HSRP groups to load share traffic from the connected hosts while providing the default router redundancy.
D. You can use the show standby command to verify HSRP operation and configuration.
E. If you remove the feature hsrp command， all relevant HSRP configuration information isalso removed.
最新試題
Which statement is true about "full state backup" in a Cisco Unified Computing System？（）
In a Cisco Unified Computing System， What is the "designated receiver" port in end-host mode used for？（）
In a Cisco Unified Computing System， where are SAN port channels connected to？（）
A Cisco Application Control Engine Appliance （ACE） non-admin context does not support "sticky" configuration. What is the reason for this issue？（）
In the event of a GSS failure in a GSS cluster， which is true？（）
What is required for Cisco UCS C-Series rack server integration with Cisco UCS Manager？（）
KAL-AP on the Cisco ACE allows communication with Cisco ACE Global Site Selector， to report virtual IP and real server availability. Which statement is true about KAL-AP？（）
An administrator is creating a service profile but receives an error when applying to a blade. The administrator checks the faults tab of the service profile and finds the following error （Refer to the exhibit）.What is the cause of this error？（）
What would be the cause for the following fault in UCS Manager？（） "ether VIF x / xxx down， reason： ENM source pinning failed"
What is the appliance port used to connect to in a Cisco Unified Computing System？（）