A. The OTV control-plane protocol uses the IS-IS protocol to establish adjacencies and exchange MAC reachability across the overlay network. You must enable IS-IS with the feature isis command before OTV adjacencies can be established.
B. OTV uses an SSM group range for neighbor discovery and to exchange MAC reachability with other OTV edge peers.
C. The OTV join interface is a routed uplink interface on the edge device used to physically join the overlay network.
D. The OTV internal interface encapsulates the site Layer 2 frames in IP unicast or multicast packets that are then sent to the other sites.
您可能感興趣的試卷
你可能感興趣的試題
A. C84C·75FA·6000
B. 01005·E11.·2FD
C. C84C·76FA·6000
D. 4000.0000.0001
A.The following XML-based NETCONF operations are supported in NX-OS SoftwarE˙close-session copy-config delete-config and edit-config
B.The following XML-based NETCONF operations are supported in NX-OS SoftwarE˙close-session copy-config edit-config and kill-session
C.NX-OS Software supports up to a maximum of 16 concurrent XML sessions
D.Only show commands are supported via the XML management interface in NX-OS Software
E.The NX-OS implementation of the XML-based NETCONF requires SSH to be used for communication with the device
A. In a vPC topology， the primary HSRP router will respond to ARP requests， but both HSRP routers will forward data traffic. No additional configuration is required.
B. In a vPC topology， the primary HSRP router will respond to ARP requests， but both HSRP routers will forward data traffic if the peer-gateway feature is enabled.
C. You can configure two overlapping HSRP groups to load share traffic from the connected hosts while providing the default router redundancy.
D. You can use the show standby command to verify HSRP operation and configuration.
E. If you remove the feature hsrp command， all relevant HSRP configuration information isalso removed.
A. Switch profiles allow configurations to be synchronized between switches and are supported with any Cisco NX-OS Software managed device.
B. DCNM LAN can archive configurations from devices even if they are not managed by the DCNM server， and the administrator can supply the device management IP address and credentials.
C. You can archive a maximum of 50 configuration versions per managed device.
D. Managed devices must be licensed in DCNM LAN before they can be used with configuration change management.
E. Device-running configuration will be archived only if it differs from the last archived version.
Nexus# conf t
Enter configuration commands， one per line. End with CNTL/Z.
Nexus（config）# interface Loopback10
% Permission denied Nexus（config）# ？
no Negate a command or set its defaults
username Configure user information.
end Go to exec mode
exit Exit from command interpreter
What is the reason why this user is not able to enter configuration commands？（）
A. The user did not enter enable prior to going into configuration mode.
B. The software license installed on Nexus is Layer 2 only， which does not allow the creation of Layer 3 interfaces.
C. The user RBAC role is set to network-operator.
D. The user failed authentication and user access defaulted to read-only mode.
E. The AAA server is currently not responding.
A. Cisco DCNM-LAN server users are local to the Cisco DCNM-LAN server. Creating， changing， and removing Cisco DCNM-LAN server users has no effect on user accounts on managed devices.
B. A Cisco DCNM-LAN server user that has Administrator privileges can push out changes to managed devices even if the Cisco NX-OS role that is used on the discovered device has the network operator role.
C. Cisco DCNM-LAN user roles restrict the ability of users to make changes to Cisco DCNM-LAN server settings. Cisco NX-OS user roles enforce read/write privileges on the discovered devices.
D. Cisco DCNM-LAN allows you to configure unique credentials for each discovered device or use default credentials when you do not configure unique credentials for a device.
E. Cisco DCNM-LAN can use AAA servers to authenticate users. Only TACACS servers are supported.
A. DHCP snooping commands are not available until the feature is enabled with the feature dhcp- snooping command.
B. When you enable the DHCP snooping feature， the switch begins building and maintaining the DHCP snooping binding database.
C. The switch will not validate DHCP messages received or use the DHCP snooping binding database to validate subsequent requests from untrusted hosts until DHCP snooping is enabled globally and for each specific VLAN.
D. Globally disabling DHCP snooping removes all DHCP snooping configuration on the switch.
E. Globally disabling DHCP snooping does not remove any DHCP snooping configuration or the configuration of other features that are dependent upon the DHCP snooping feature.
A. The AED is responsible for sending all unicast traffic in a site， while either node in a site can transmit multicast and broadcast.
B. The AED is responsible for load balancing all traffic for all VLANs across the transport network.
C. The AED is responsible for handling all unicast， broadcast， and multicast traffic for a given VLAN within a site.
D. The AED is responsible for MAC address dispute contention for a given VLAN.
A. The verify command will validate commands entered for syntax errors.
B. The save command will save the commands entered to the startup configuration.
C. The network administrator can perform a dry-run ACL configuration by verifying the configuration against the hardware and software resources available before applying it.
D. Configuration sessions can be saved and resumed at any time， even after upgrading NX-OS Software on the switch with ISSU.
E. Configuration sessions are global for all VDCs on the Nexus 7000.
A. Improves convergence of the multicast network due to enhanced RPF checks
B. Simplifies the number of control plane protocols over other RP redundancy methods
C. Eliminates the use of Protocol Independent Multicast （PIM） in the topology
D. Increases the administrative distances in Multicast Source Discovery Protocol （MSDP） configuration
最新試題
Your company wants Server 1/eth0 （vNIC 1） configured so that it always uses Fabric Interconnect A Port Channel 1 （Po1） when it communicates with anything outside of the Cisco UCS domain. However， if vNIC 1 fails over to Fabric Interconnect B using fabric failover， then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true？ （）
Refer to the exhibit.The Cisco UCS domain is operating in switching mode. A network administrator notices that no traffic is traversing the uplinks on Fabric Interconnect B （Path C）. Which actions might be used to change this behavior？（）
What is the appliance port used to connect to in a Cisco Unified Computing System？（）
On a Cisco Unified Computing System （UCS）， which two statements regarding Ethanalyzer are true？（）
Server load balancing （SLB） is the process of deciding to which server a load-balancing device should send a client request for service. Which predictors are supported on ACE in order to select the best server to fulfill a client request？ （）
From the Cisco UCS CLI， how do you verify which uplink ports a blade server is using for its network connectivity？（）
What is the purpose of this command in a Cisco Application Control Engine？（） switch/Admin# show np 1 me-stats "-F0 v"
Given a Cisco Unified Computing System， which is a valid port type in end-host mode？（）
What interface is created when an FC Port Channel is created on a Cisco Unified Computing System？（）
A Cisco UCS fabric interconnect in end-host mode learns MAC addresses on which port types？（）