A. Only to Cisco Fibre Channel switches
B. Only to Cisco Fibre Channel switches in NPIV mode
C. To any Fibre Channel switch
D. Directly to storage arrays
E. Only to Nexus Switches
您可能感興趣的試卷
你可能感興趣的試題
A. Under the Admin tab on the FI
B. Under the Server tab in the service profile
C. Under the SAN tab on each VSAN
D. Under the Admin tab on the chassis
E. Under the SAN tab on the Fabric Interconnect
Given the following output：
san-port-channel 12 is up
Hardware is Fibre Channel
Port WWN is 24：0c：00：0d：ec：d3：5c：00
Admin port mode is NP， trunk mode is on
Port mode is NP Port vsan is 1
Speed is 8 Gbps
Member[1] ： fc2/3
Member[2] ： fc2/4
What does "Speed is 8 Gbps" indicate？（）
A. The speed of the slowest interface in the port channel
B. The combined speed of all interfaces configured in the port channel
C. The combined speed of all interfaces in the port channel that are up
D. The speed that can be achieved if all buffers are used
A. Server
B. End device
C. Node
D. Host
E. Virtual
A. Sending all broadcasts
B. Receiving all traffic from upstream switches
C. Receiving broadcast traffic
D. Negotiating spanning tree with upstream switches
E. Learning MAC addresses from upstream switches
A. The Cisco VIC can create an unlimited number of Virtual NICs
B. The number of vNICs on the Cisco VIC that can be created is determined by the number of chassis uplinks
C. vNICs are created using software on the host operating system
D. The host operating system sees a vNIC as a physical PCIe device
E. The host operating system sees a vNIC as a sub-interface of a primary NIC
F. The Cisco VIC can create 1024 vNICs
A. Fibre Channel storage
B. UCS C-Series servers
C. NFS storage
D. UCS chassis
E. Other fabric interconnect
A. End-host mode is synonymous with NPV mode.
B. In end-host mode， only hard pinning of vHBAs to Fibre Channel uplink ports is allowed.
C. Making configuration changes between Fibre Channel switching mode and end-host mode is nondisruptive.
D. End-host mode is the default Fibre Channel switching mode.
A. In the blade BIOS
B. In the operating system
C. In the service profile
D. In the card option ROM
A. The QoS policy assigns a system class to the outgoing traffic for a vNIC or vHBA.
B. Flow-control policies determine whether the uplink Ethernet ports in a Cisco UCS environment send and receive IEEE 802.3x pause frames when the send buffer for a port fills.
C. If no system class is configured as CoS 0， the Fibre Channel system class is used.
D. The user can configure QoS for these system classes： platinum， gold， silver， best effort， Fibre Channel.
E. When configuring a system class， the type of adapter in a server may limit the maximum MTU supported.
A. boot policy and BIOS policy
B. disk scrub and boot policy
C. BIOS setting scrub， boot policy， and BIOS policy
D. disk scrub and BIOS setting scrub
最新試題
A Cisco UCS fabric interconnect in end-host mode learns MAC addresses on which port types？（）
Application Control Engine （ACE） can check the health of servers and server farms by configuring health probes （which are sometimes referred to as keepalives）. A probe can be one of many types. Which are valid ACE probes？ （）
An administrator creates a vNIC and assigns it to Fabric A with the fabric failover feature enabled. Which statement is true？（）
In a Cisco Unified Computing System， where are SAN port channels connected to？（）
Refer to the exhibit.Your company requires a Cisco UCS configuration that will， at a minimum， allow the configuration in the provided exhibit. Which Cisco UCS components will meet the requirement？（）
Which statement is true about "full state backup" in a Cisco Unified Computing System？（）
On a Cisco Unified Computing System （UCS）， which two statements regarding Ethanalyzer are true？（）
Which of the following are supported in Cisco Global Site Selector？ （）
In a Cisco Unified Computing System， What is the "designated receiver" port in end-host mode used for？（）
Which is true when describing a connection replication in Cisco ACE？（）