A. Join interface is a Layer 3 entity， and with the Cisco NX-OS release 6.0， it can only be defined as a physical interface， physical subinterface， Layer 3 port channel， or Layer 3 port channel subinterface.
B. A single join interface can be defined and associated with a given OTV overlay.
C. Multiple overlays can also share the same join interface.
D. Join interface can be a loopback interface.
E. The join interface is a Layer 3 entity that can be defined as a physical interface but not as a logical one.
您可能感興趣的試卷
你可能感興趣的試題
The network administrator is seeing N7K-1 having issues with VLAN 11， and interface VLAN 11 is resetting， causing frequent HSRP state changes. Which two actions would reduce HSRP state changes？ （）
A..On N7K-1，configure the HSRP extended hold timer to 180， extending the HSRP hello message hold time.
B..On N7K-2，configure the HSRP extended hold timer to 180， extending the HSRP hello message hold time.
C..On N7K-1，configure the pre-empt delay minimum to 180 in order to delay N7K-1 from taking over as the HSRP active router.
D..On N7K-2，configure the pre-empt delay minimum to 180 in order to delay N7K-2 from taking over as the HSRP active router.
E..On N7K-2，increase the HSRP priority to 150.
F. On N7K-2，decrease the HSRP priority to 50.
A. When an OTV edge device receives a Layer 2 frame destined for a remote data center site， the frame is logically forwarded to the overlay interface.
B. The OTV edge device performs the dynamic OTV encapsulation on the Layer 2 packet and sends it to the join interface toward the routed domain.
C. When the OTV edge device receives a Layer 2 frame destined for a remote data center site， the frame is logically forwarded to the join interface.
D. The OTV edge device performs the dynamic OTV encapsulation on the Layer 2 packet and sends it to the overlay interface toward the routed domain.
A. port-profile
B. command
C. access-list
D. feature-group
E. OID
A. Enable feature vPC
B. Define domains
C. Establish peer keepalive connectivity
D. Create a peer link
E. Configure the peer link as a trunk port
F. Create port channels and vPCs
G. Define port channel load-balancing method
H. Make sure configurations are consistent
A. UCS Manager XML API and UCS CLI
B. SNMP， SMASH CLP， and CIM-XML
C. UCS Manager， DCOS， and Local-mgmt
D. SoL and NX-OS
E. debug-plugin and UCS Manager GUI
最新試題
Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager？ （）
What would be the cause for the following fault in UCS Manager？（） "ether VIF x / xxx down， reason： ENM source pinning failed"
Which is true when describing a connection replication in Cisco ACE？（）
Application Control Engine （ACE） can check the health of servers and server farms by configuring health probes （which are sometimes referred to as keepalives）. A probe can be one of many types. Which are valid ACE probes？ （）
In a Cisco Unified Computing System， where are SAN port channels connected to？（）
Given a Cisco Unified Computing System， which is a valid port type in end-host mode？（）
Refer to the exhibit.Your company requires a Cisco UCS configuration that will， at a minimum， allow the configuration in the provided exhibit. Which Cisco UCS components will meet the requirement？（）
KAL-AP on the Cisco ACE allows communication with Cisco ACE Global Site Selector， to report virtual IP and real server availability. Which statement is true about KAL-AP？（）
Given the following output： san-port-channel 12 is up Hardware is Fibre Channel Port WWN is 24：0c：00：0d：ec：d3：5c：00 Admin port mode is NP， trunk mode is on Port mode is NP Port vsan is 1 Speed is 8 Gbps Member[1] ： fc2/3 Member[2] ： fc2/4 What does "Speed is 8 Gbps" indicate？（）
When will an "all configuration" backup be imported into the Cisco UCS Manager？（）