On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter，the status LED and activity LED are alternating on and off.
What does this indicate？（）
A.The client card has failed.
B.The client card is not associated to the network.
C.The driver has been installed incorrectly.
D.The client card has awakened from power-save mode.
您可能感興趣的試卷
你可能感興趣的試題
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.
What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）
A.25 percent
B.40 percent
C.55 percent
D.75 percent
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.
What does this indicate about the access point？（）
A.normal operation
B.duplicate IP address
C.code upgrade in progress
D.searching for primary controller
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.
What is the maximum number of WLAN controllers that you can add？（）
A.12
B.17
C.20
D.24
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.
Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
A.Transmit Mobile Anchor Export message
B.Receive Mobile Anchor Export message
C.Transmit Plumbing duplex mobility tunnel message
D.Receive Plumbing duplex mobility tunnel message
A.4
B.8
C.16
D.32
最新試題
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter，the status LED and activity LED are alternating on and off.What does this indicate？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）
Which of the following commands on the wireless interface of a Cisco 3845 Integrated Service Router allows the SSID to broadcast？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue and blinking，but the status LED and Ethernet LED are both off.What does this indicate？（）
An REAP was supporting 16 WLANs， but now it only supports one.What happened to cause the change？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton， you should verify that the file name is which of the following？（）
You are trying to change the polling parameters used by the location manager via the Cisco WCS，and your request is being denied. What is wrong？（）
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）