Refer to the exhibit. Based upon the debug output that is shown，
which three statements about HSRP are true？（）
A. The router with IP address 172.16.11.111 haspreempt configured.
B. The final active router is the router with IP address 172.16.11.111.
C. The router with IP address 172.16.11.112 has nonpreempt configured.
D. The priority of the router with IP address 172.16.11.112 is preferred over the router with IP address 172.16.11.111.
E. The router with IP address 172.16.11.112 is using default HSRP priority.
F. The IP address 172.16.11.115 is the virtual HSRP IP address.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit.
Which two problems are the most likely cause of the exhibited output？（）
A. transport layer issues
B. VRRP misconfiguration
C. HSRP misconfiguration
D. physical layer issues
E. spanning tree issues
Examine the router output above. Which two items are correct？（）
A. The local IP address of Router A is 10.1.0.6.
B. The local IP address of Router A is 10.1.0.20.
C. If Ethernet 0/2 goesdown， the standby router will take over.
D. When Ethernet 0/3 of RouterA comes back up， the priority will become 105.
E. Router A will assume the active state if its priority is the highest.
What can be determined about the HSRP relationship from the displayed debug output？ （）
A. Router 172.16.11.112 will be the active router because its HSRP priority is preferred over router 172.16.11.111.
B. Router 172.16.11.111 will be the active router because its HSRP priority is preferred over router 172.16.11.112.
C. The IP address 172.16.11.111 is the virtual HSRP router IP address.
D. The IP address 172.16.11.112 is the virtual HSRP router IP address.
E. The nonpreempt feature is enabled on the 172.16.11.112 router.
F. The preempt feature is not enabled on the 172.16.11.111 router.
Refer to the exhibit. Based upon the debug output that is shown，
which three statements about HSRP are true？（）
A. The router with IP address 172.16.11.111 haspreempt configured.
B. The final active router is the router with IP address 172.16.11.111.
C. The router with IP address 172.16.11.112 has nonpreempt configured.
D. The priority of the router with IP address 172.16.11.112 is preferred over the router with IP address 172.16.11.111.
E. The router with IP address 172.16.11.112 is using default HSRP priority.
F. The IP address 172.16.11.115 is the virtual HSRP IP address.
A. independent of SSO
B. NSF combined with SSO enables supervisor engine load balancing
C. supported by RIPv2， OSPF， IS-IS， and EIGRP
D. supports IPv4 and IPv6 multicast
E. prevents route flapping
F. dependent on FIB tables
最新試題
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Which statement is correct about the use of the virtual interface on a WLC ？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Which statement is correct about RSTP port roles？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）