Router R1 is configured for HSRP.
Which of the following are valid HSRP states on R1？ （）
A. Init
B. Idle
C. Active
D. Standby
E. Established
F. Backup
您可能感興趣的試卷
你可能感興趣的試題
You have configured router R1 with HSRP， using the standard defaults.
Which three statements are true of a default HSRP configuration？（）
A. The Standby hello time is 2 seconds.
B. Two HSRP groups are configured.
C. The Standby track interface priority is 10.
D. The Standby hold time is 10 seconds
E. The Standby priority is 100.
F. The Standby delay is 3 seconds.
You need to design router redundancy on the Company network.
Which three protocols could be chosen for IP routing redundancy to protect against first-hop router failure？（）
A. GLBP
B. ICMP
C. MSTP
D. HSRP
E. VRRP
F. NHRP
Router R1 and R2 are both configured for HSRP.
Which two statements about the HSRP priorities of these two routers are true？（）
A. To assign the HSRP router priority in a standby group， the standby group-number priority priority-value global configuration command must be used.
B. The default priority of a router is zero （0）.
C. The no standby priority command assigns a priority of 100 to the router.
D. Assuming that preempting has also been configured， the router with the lowest priority in an HSRP group would become the active router.
E. When two routers in an HSRP standby group are configured with identical priorities， the router with the highest configured IP address will become the active router.
Which first-hop redundancy solution listed would supply Company clients with MAC address0000.0C07.AC0A for group 10 in response to an ARP request for a default gateway？（）
A. IRDP
B. Proxy ARP
C. GLBP
D. HSRP
E. VRRP
F. IP Redirects
You work as a network technician at Company. Your boss， Mrs. ， is interested in
GLBP. In particular， she wants to know the multicast address that this protocol uses.
What should you tell her？ （）
A. 224.0.0.100
B. 224.0.0.1
C. 224.0.0.102
D. 224.0.0.10
E. 224.0.0.101
F. None of the other alternatives apply
最新試題
Which statement is correct about the use of the virtual interface on a WLC ？（）
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Which two statements are true when the extended system ID feature is enabled？ （）
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）