Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1.
What will be the result？（）
A.The command will be rejected by the switch.
B.Interfaces FastEthernet0/13 and FastEthernet0/14 will no longer be bundled.
C.Dynamic Trunking Protocol will be turned off on interfaces FastEthernet0/13 and FastEthernet0/14.
D.Interfaces FastEthernet0/13 and FastEthernet0/14 will only allow traffic from the native VLAN.
E.Interfaces FastEthernet0/13 and FastEthernet0/14 will continue to pass traffic for VLANs 88，100，360.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit.
What will happen when one more user is connected to interface FastEthernet 5/1？ （）
A.All secure addresses will age out and be removed from the secure address list. This will cause the security violation counter to increment.
B.The first address learned on the port will be removed from the secure address list and be replaced with the new address.
C.The interface will be placed into the error-disabled state immediately， and an SNMP trap notification will be sent.
D.The packets with the new source addresses will be dropped until a sufficient number of secure MAC addresses are removed from the secure address list.
Refer to the exhibit. LACP has been configured on Switch1 as shown.
Which is the correct command set to configure LACP on Switch2？（）
A.Switch2# configure terminal Switch2（config）# interface range gigabitethernet3/1 -2 Switch2（config-if）# channel-group 5 mode auto
B.Switch2# configure terminal Switch2（config）# interface range gigabitethernet3/1 -2 Switch2（config-if）# channel-group 5 mode passive
C.Switch2# configure terminal Switch2（config）# interface range gigabitethernet3/1 -2 Switch2（config-if）# channel-group 5 mode desirable
D.Switch2# configure terminal Switch2（config）# interface range gigabitethernet3/1 -2 Switch2（config-if）# channel-group 5 mode on
Refer to the exhibit.
What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
A.ip routing
B.no ip routing
C.router eigrp 1
D.no router eigrp 1
E.mls qos
F.no mls qos
A.VLAN instance mapping and revision number
B.VLAN instance mapping and member list
C.VLAN instance mapping， revision number， and member list
D.VLAN instance mapping， revision number， member list， and timers
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct，
what will be true about Switch 15？（）
A.All ports will be in forwarding mode.
B.All ports in VLAN 10 will be in forwarding mode.
C.All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in blocking mode.
D.All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in standby mode.
最新試題
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）
Refer to the exhibit. Which statement is true about the output？（）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）