Which one of the statements below correctly describes the Virtual Router Redundancy Protocol （VRRP），
which is being used in the Company network to provide redundancy？（）
A. A VRRP group has one active and one or more standby virtual routers.
B. A VRRP group has one master and one or more backup virtual routers.
C. A VRRP group has one master and one redundant virtual router.
D. None of the other alternatives apply
您可能感興趣的試卷
你可能感興趣的試題
HSRP has been configured between two Company devices.
What kind of message does an HSRP configured router send out every 3 seconds？（）
A. Retire
B. Coup
C. Resign
D. Send
E. Hello
To protect against first-hop router failure， four protocols were developed to ensure IP routing redundancy.
Which of the following are they？（）
A. HSRP
B. IRDP
C. ICMP
D. VRRP
E. MSTP
F. GLBP
HSRP is being set up between two Company devices.
In what three states is it possible for an HSRP router to be in？（）
A. Standby
B. Established
C. Active
D. Idle
E. Backup
F. Init
R1 and R2 exchange HSRP between each other in the Company network.
In which three HSRP states do routers send hello messages？（）
A. Learn
B. Speak
C. Standby
D. Listen
E. Active
F. Remove
You need to implement a high availability design in the Company routed network.
Which protocol allows for the automatic selection and simultaneous use of multiple available gateways as well as automatic failover between those gateways？（）
A. VRRP
B. GLBP
C. IRDP
D. HSRP
E. None of the other alternatives apply
最新試題
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command， which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true？（）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）