A. 228.10.10.7
B. 229.11.10.7
C. 229.138.10.7
D. 229.138.10.8
E. 228.10.10.8
F. 228.10.138.7
您可能感興趣的試卷
你可能感興趣的試題
A. 169.254.23.59
B. 223.254.255.254
C. 225.1.1.1
D. 227.43.34.2
E. 238.3.3.3
F. 249.1.2.3
A. acts as a meeting place for sources and receivers of multicast traffic
B. used in PIM dense m ode to create a database of all multicast sources
C. used in PIM dense and sparse mode to create a database of all multicast sources
D. acts as the designated router for a broadcast segment when multicast routing is enabled
Refer to the exhibit. IP multicast for group address 224.1.1.1 has been enabled on all router s in the network. Hosts on Network A receive the multicast traffic. However, hosts on Network B do not. On the basis of outputs provided, what could be the cause of the problem? （）
A. The route to 224.69.15.0/24 will be out Ethernet 0
B. The reverse path forwarding (RPF) for the route 224.2.0.1 failed to find the interface on which the multicast packet was rece ived
C. Multicast route to 224.69.15.0/24 was added to the mroute table and created by a source directly connected to the router
D. Multicast route to 10.16.0.0/16 was added to the mroute table and created by a source directly connected to the router
E. This router received an IGMP host report from a group member or a PIM join message
A. IGMP snooping and Cisco Group Membership Protocol (CGMP) can be used simultaneously on a switch.
B. IGMP snooping a nd Cisco Group Membership Protocol (CGMP) were developed to help Layer 3 switches make intelligent forwarding decisions on their own.
C. IGMP snooping examines IGMP join/leave messages so that multicast traffic is forwarded only to hosts that sent an IG MP message toward the router.
D. IGMP snooping is an IP multicast constraining mechanism for Layer 2 switches.
E. IGMP snooping is enabled with the ip multicast - routing global configuration command.
A. There are three IGMP modes: dense mode, sparse mode, and sparse - dense mode
B. IGMP is used to register individual hosts with a multicast group
C. IGMP version 3 enables a multicast receiving host to specify to the router which sources it should forward traffic from
D. IGMP messages a re IP datagrams with a protocol value of 2, destination address of 224.0.0.2, and a TTL value of 1
E. IGMP is a multicast routing protocol that makes packet - forwarding decisions independent of other routing protocols such as EIGRP
F. IGMP snooping ru ns on Layer 3 routers
最新試題
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?（）
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
Which of the following are true of both OSPFv2 and OSPFv3?（）
Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE.Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?（）
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1