A. acts as a meeting place for sources and receivers of multicast traffic
B. used in PIM dense m ode to create a database of all multicast sources
C. used in PIM dense and sparse mode to create a database of all multicast sources
D. acts as the designated router for a broadcast segment when multicast routing is enabled
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. IP multicast for group address 224.1.1.1 has been enabled on all router s in the network. Hosts on Network A receive the multicast traffic. However, hosts on Network B do not. On the basis of outputs provided, what could be the cause of the problem? （）
A. The route to 224.69.15.0/24 will be out Ethernet 0
B. The reverse path forwarding (RPF) for the route 224.2.0.1 failed to find the interface on which the multicast packet was rece ived
C. Multicast route to 224.69.15.0/24 was added to the mroute table and created by a source directly connected to the router
D. Multicast route to 10.16.0.0/16 was added to the mroute table and created by a source directly connected to the router
E. This router received an IGMP host report from a group member or a PIM join message
A. IGMP snooping and Cisco Group Membership Protocol (CGMP) can be used simultaneously on a switch.
B. IGMP snooping a nd Cisco Group Membership Protocol (CGMP) were developed to help Layer 3 switches make intelligent forwarding decisions on their own.
C. IGMP snooping examines IGMP join/leave messages so that multicast traffic is forwarded only to hosts that sent an IG MP message toward the router.
D. IGMP snooping is an IP multicast constraining mechanism for Layer 2 switches.
E. IGMP snooping is enabled with the ip multicast - routing global configuration command.
A. There are three IGMP modes: dense mode, sparse mode, and sparse - dense mode
B. IGMP is used to register individual hosts with a multicast group
C. IGMP version 3 enables a multicast receiving host to specify to the router which sources it should forward traffic from
D. IGMP messages a re IP datagrams with a protocol value of 2, destination address of 224.0.0.2, and a TTL value of 1
E. IGMP is a multicast routing protocol that makes packet - forwarding decisions independent of other routing protocols such as EIGRP
F. IGMP snooping ru ns on Layer 3 routers
A. PIM sparse - dense
B. Bidir - PIM
C. PIM - RP
D. PIM - DM
E. PIM - SM
A. membership query message
B. membership report message
C. leave group message
D. source filtering
E. destination filtering
最新試題
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Which of the following answers lists a multicast IPv6 address?（）
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
Which of the following features work the same in both RIP- 2 and RIPng?（）