Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Cisco 642-832： Practice Exam
Figure 2
Trouble Ticket Statement
HSRP has been configurationured between DSW1 and DSW2. DSW1 is configurationured to be activerouter but it never becomes active even though the HSRP communication between DSW1 and DSW2 isworking.
Configuration on DSW1
CertKiller.com
track 1 ip route 10.1.21.128 255.255.0.0 metric threshold threshold metric up 1 down 2!
track 10 ip route 10.2.21.128 255.255.255.0 metric threshold threshold metric up 63 down 64!
interface Vlan10
ip address 10.2.1.1 255.255.255.0
standby 10 ip 10.2.1.254
standby 10 priority 200
standby 10 preempt
standby 10 track 1 decrement 60
Configuration on R4
Cisco 642-832： Practice Exam
interface loopback0
ip address 10.2.21.128 255.255.255.0
What is the solution of fault condition？（）
A.Change standby priority to 140
B.Change standby priority to 260
C.Change standby 10 track 1 decrement 60 to standby 10 track 10 decrement 60
D.Change standby 10 track 1 decrement 60 to standby 10 track 1 decrement 100
您可能感興趣的試卷
你可能感興趣的試題
Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Cisco 642-832： Practice Exam
Figure 2
Trouble Ticket Statement：
Client 1 is able to ping 10.1.1.2 but not 10.1.1.1. Initial troubleshooting shows that R1 does not have anyOSPF neighbors or any OSPF routes
Configuration on R1：
router ospf 1
CertKiller.com
log-adjacency-changes
network 10.1.1.0 0.0.0.3 area 12
default-information originate always!
interfaceSerial0/0/0/0.12 point-to-point
ip address 10.1.1.1 255.255.255.252
ip nat inside
ip ospf message-digest-key 1 md5 TSHOOT
Configuration on R2：
router ospf 1
log-adjacency-changes
network 10.1.1.0 0.0.0.3 area 12!
Cisco 642-832： Practice Exam
interfaceSerial0/0/0/0.12 point-to-point
ip address 10.1.1.2 255.255.255.252
ip ospf authentication message-digest
ip ospf message-digest-key 1 md5 TSHOOT
What is the solution of the fault condition？（）
A.ipospf authentication message-digestcommand has to be added on S0/0/0/0.12
B.ipospf authentication message-digestcommand has to be added under the OSPF routing process
C.A static route to 10.1.1.4 must be added on R1
D.ipnat outside must be added on S0/0/0/0.12
最新試題
Study the exhibit carefully. The Cisco IOS IPsec High Availability （IPsec HA） Enhancementsfeature provides an infrastructure for reliable and secure networks to provide transparent availability of the VPN gateways - that is， Cisco IOS Software-based routers. What are the twooptions that are used to provide High Availability IPsec？（）
Authentication is the process of determining if a user or identity is who they claim to be. Refer tothe exhibit. Which statement about the authentication process is correct？（）
In computer security， AAA stands for authentication， authorization and accounting. Which optionabout the AAA authentication enable default group radius enable command is correct？（）
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）
Drag each element of the Cisco IOS Firewall Feature Set from the above and drop onto itsdescription on the below.
Drag and drop the steps in the process for provisioning a cable modem to connect to a headendon the above to the below in the order defined by the DOCSIS standard.
As a network engineer， do you know for what purpose SDM uses Security Device Event Exchange（SDEE）？（）
IPSec VPN is a widely-acknowledged solution for enterprise network. What are the four steps tosetup an IPsec VPN？（）
A new router was configured with the following commands：The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clicking the numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible.To gain access to either the topology or the SDK click on the button to left side of the screen thatcorresponds to the section you wish to access. When you have finished viewing the topology theSDK you can return to your questions by clicking on the Questions button to the left.Which defined peer IP address an local subnet belong to Crete？（）