Authentication is the process of determining if a user or identity is who they claim to be. Refer tothe exhibit. Which statement about the authentication process is correct？（）
A.The LIST1 list will disable authentication on the console port
B.All login requests will be authenticated using the group tacacs+ method
C.The default login authentication will automatically be applied to all login connections
D.Because no method list is specified， the LIST1 list will not authenticate anyone on the consoleport
您可能感興趣的試卷
你可能感興趣的試題
A.to provide a keepalive mechanism
B.to pull event logs from the router
C.to extract relevant SNMP information
D.to perform application-level accounting
A.Disable post scan
B.Use SSH or SSL
C.Enable trust levels
D.Deny echo replies on all edge routers
Network Topology Exhibit：
Configuration Exhibit：
NET（config）# access-list 112 deny icmp any any echo log
NET（config）# access-list 112 deny imp any any redirect log
NET（config）# access-list 112 deny icmp any any mask-request log
NET（config）# access-list 112 permit icmp any 10.1.1.0 0.0.0.255
NET（config）# interface Fa0/1
NET（config-if）# ip access-group 112 in
You work as a network administrator at networkTut.com， study the exhibit carefully. The
configuration has been applied to router NET to mitigate the threat of certain types of ICMPbasedattacks while allowing some ICMP traffic to the corporate LAN to work. However， the configurationis incorrect. On the basis of the information in the exhibit， which configuration option wouldcorrectly configure router NET？（）
A.The first three statements of ACL 112 should have permitted the ICMP traffic and the laststatement should deny the identified traffic
B.The last statement of ACL 112 should have been "access-list 112deny icmp any 10.2.1.00.0.0.255"
C.The last statement of ACL 112 should have been "access-list 112permit icmp any 10.2.1.00.0.0.255"
D.ACL 112 should have been applied to interface Fa0/0 in an inbound direction
E.The last statement of ACL 112 should have been "access-list 112deny icmp any 10.1.1.00.0.0.255"
F.ACL 112 should have been applied to interface Fa0/1 in an outbound direction
G.None of the above
A.The dsl operating-mode auto command is required if the default mode has been changed
B.The ip mtu 1496 command must be applied on the dialer interface
C.The encapsulation ppp command is required
D.The ip mtu 1492 command must be applied on the dialer interface
As a network engineer， study the exhibit carefully. Router Net is unable to establish an ADSLconnection with its provider. Which action would correct this problem？（）
A.On the Dialer0 interface， add the pppoe enable command
B.On the Dialer0 Interface， add the ip mtu 1496 command
C.On the ATM0/0 interface， add the dialer pool-member 1 command
D.On the ATM0/0 interface， add the dialer pool-member 0 command
最新試題
Drag and drop question. The upper gives the MPLS functions， the bottom describes the planes.Drag the above items to the proper location at the below
Drag and drop each management protocol on the above to the correct category on the below.
Drag the IOS commands from the left that would be used to implement a GRE tunnel using the10.1.1.0.30 network on interface serial 0/0 to the correct target area on the right.
Match the xDSL type on the above to the most appropriate implementation on the below.
A new router was configured with the following commands：The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
Identify the recommended steps for worm attack mitigation by dragging and dropping them into thetarget area in the correct order.
As a network technician， do you know what is a recommended practice for secure configurationmanagement？（）
Study this exhibit carefully. What information can be derived from the SDM firewall configurationdisplayed？（）
Drag the DSL technologies on the left to their maximum（down/up） data rate values on the below.
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）