A. DHCP snooping commands are not available until the feature is enabled with the feature dhcp- snooping command.
B. When you enable the DHCP snooping feature, the switch begins building and maintaining the DHCP snooping binding database.
C. The switch will not validate DHCP messages received or use the DHCP snooping binding database to validate subsequent requests from untrusted hosts until DHCP snooping is enabled globally and for each specific VLAN.
D. Globally disabling DHCP snooping removes all DHCP snooping configuration on the switch.
E. Globally disabling DHCP snooping does not remove any DHCP snooping configuration or the configuration of other features that are dependent upon the DHCP snooping feature.
您可能感興趣的試卷
你可能感興趣的試題
A. The AED is responsible for sending all unicast traffic in a site, while either node in a site can transmit multicast and broadcast.
B. The AED is responsible for load balancing all traffic for all VLANs across the transport network.
C. The AED is responsible for handling all unicast, broadcast, and multicast traffic for a given VLAN within a site.
D. The AED is responsible for MAC address dispute contention for a given VLAN.
A. The verify command will validate commands entered for syntax errors.
B. The save command will save the commands entered to the startup configuration.
C. The network administrator can perform a dry-run ACL configuration by verifying the configuration against the hardware and software resources available before applying it.
D. Configuration sessions can be saved and resumed at any time, even after upgrading NX-OS Software on the switch with ISSU.
E. Configuration sessions are global for all VDCs on the Nexus 7000.
A. Improves convergence of the multicast network due to enhanced RPF checks
B. Simplifies the number of control plane protocols over other RP redundancy methods
C. Eliminates the use of Protocol Independent Multicast (PIM) in the topology
D. Increases the administrative distances in Multicast Source Discovery Protocol (MSDP) configuration
2012 Feb 23 23:00:08.676710 pim: [16132] (default-base) Received unauthenticated hello- message from 10.1.1.2 on Ethernet1/18, message discarded 2012 Feb 23 23:00:12.528763 pim: [16132] (default-base) Send Hello with AH on Ethernet1/18 from 10.1.1.1, holdtimE. 105 secs,dr-priority:1
You are troubleshooting a PIM neighbor adjacency that is not coming up. You issued the command show ip pim neighbor e1/18 and confirmed there is no PIM neighbor on the interface. What is the problem based on the debug output?()
A. The peer router 10.1.1.2 has PIM disabled on its interface connecting to Ethernet1/18.
B. The peer router 10.1.1.2 has the wrong PIM password configured on its interface connecting to Ethernet1/18.
C. The local router 10.1.1.1 has the wrong PIM password configured on Ethernet1/18.
D. The peer router 10.1.1.2 does not have PIM hello authentication enabled on its interface connecting to Ethernet1/18.
E. The local router 10.1.1.1 does not have PIM hello authentication enabled for Ethernet1/18.
A. The supervisor module enforces CoPP before out-of-policy traffic reaches the CPU
B. The fabric modules enforce CoPP in the fabric before out-of-policy traffic reaches the CPU
C. The linecards enforce CoPP locally before out-of-policy traffic reaches the CPU
D. The egress virtual output queue enforces CoPP locally before out-of-policy traffic reaches the CPU
A. on all ingress interfaces; to ensure maximum throughput on a per-egress, per-CoS basis
B. on all ingress interfaces; to provide independent congestion management and 16 queues
C. on all egress interfaces; so that a congested egress port does not affect traffic directed to other egress ports
D. on all egress interfaces; to prevent head-of-line blocking by utilizing multiple virtual output queues
E. on all egress interfaces; to be able to use EEE 802.1p CoS
A. VRRP does not work with vPC due to industry standard requirements
B. VRRP works with vPC in traditional active/standby modes
C. VRRP works with vPC in an active/active mode
D. VRRP work with vPC as long as vPC peer-gateway is configured to address non-standard replies to the physical MAC address
A. It enables MAC ACLs to be applied to only IP packets that enter the interface.
B. It enables MAC ACLs to be applied to only non-IP packets that enter the interface.
C. It enables MAC ACLs to be applied to all packets that enter the interface.
D. It enables MAC ACLs to be used for QoS settings.
A. EPLD upgrade, IOS ISSU, FCoE feature enablement, CoPP configuration, and rolling back a checkpoint
B. EPLD upgrade, Cisco IOS ISSU, FCoE feature enablement, CoPP configuration, and ACL capture enablement
C. EPLD upgrade, Cisco IOS ISSU, FCoE feature enablement, CoPP configuration and SNMP configuration
D. EPLD upgrade, Cisco IOS ISSU, FCoE feature enablement, CoPP configuration, and write erase
A. They make it easier to manage user logins and passwords across devices.
B. They enable automated configuration backup for devices.
C. They centrally manage user attributes and permissions.
D. Local console access is never included in AAA and can be used for access when the AAA servers are down.
最新試題
What is the appliance port used to connect to in a Cisco Unified Computing System?()
Your company wants Server 1/eth0 (vNIC 1) configured so that it always uses Fabric Interconnect A Port Channel 1 (Po1) when it communicates with anything outside of the Cisco UCS domain. However, if vNIC 1 fails over to Fabric Interconnect B using fabric failover, then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true? ()
Which statement is true regarding Backup tasks in Cisco UCS?()
Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager? ()
What is the purpose of this command in a Cisco Application Control Engine?() switch/Admin# show np 1 me-stats "-F0 v"
Refer to the exhibit.Your company requires a Cisco UCS configuration that will, at a minimum, allow the configuration in the provided exhibit. Which Cisco UCS components will meet the requirement?()
In the event of a GSS failure in a GSS cluster, which is true?()
In a Cisco Unified Computing System, What is the "designated receiver" port in end-host mode used for?()
What would be the cause for the following fault in UCS Manager?() "ether VIF x / xxx down, reason: ENM source pinning failed"
A Cisco UCS fabric interconnect in end-host mode learns MAC addresses on which port types?()