單項選擇題

Refer to the exhibit. A network technician is asked to design a small network with redundancy. The exhibit represents this design, with all hosts configured in the same VLAN. What conclusions can be made about this design?（）

A.The design will function as intended
B.Spanning-tree will need to be used.
C.The router will not accept the addressing scheme.
D.The connection between switches should be a trunk.
E.The router interfaces must be encapsulated with the 802.1Q protocol.


您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題Cisco Catalyst switches CAT1 and CAT2 have a connection between them using ports FA0/13. An 802.1Q trunk is configured between the two switches. On CAT1, VLAN 10 is chosen as native, but on CAT2 the native VLAN is not specified.What will happen in this scenario?（）

A.802.1Q giants frames could saturate the link.
B.VLAN 10 on CAT1 and VLAN 1 on CAT2 will send untagged frames.
C.A native VLAN mismatch error message will appear.
D.VLAN 10 on CAT1 and VLAN 1 on CAT2 will send tagged frames.

2.多項選擇題Host 1 is trying to communicate with Host 2. The e0 interface on Router C is down. Which of the following are true?（）

A.Router C will use ICMP to inform Host 1 that Host 2 cannot be reached.
B.Router C will use ICMP to inform Router B that Host 2 cannot be reached.
C.Router C will use ICMP to inform Host 1, Router A, and Router B that Host 2 cannot be reached.
D.Router C will send a Destination Unreachable message type.
E.Router C will send a Router Selection message type.
F.Router C will send a Source Quench message type.

3.單項選擇題When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?（）

A.show ip access-list
B.show access-list
C.list ip interface
D.show interface
E.show ip interface

4.單項選擇題Which Cisco Catalyst feature automatically disables the port in an operational PortFast upon receipt of a BPDU?（）

A.BackboneFast
B.UplinkFast
C.Root Guard
D.BPDU Guard
E.BPDU Filter

5.單項選擇題A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem? （）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0

A.The process id is configured improperly
B.The OSPF area is configured improperly
C.The network wildcard mask is configured improperly
D.The network number is configured improperly
E.The AS is configured improperly
F.The network subnet mask is configuerd improperly

6.單項選擇題

Users on the 172.17.22.0 network cannot reach the server located on the 172.31.5.0 network.The network administrator connected to console port,issued the show ip route command,and was able to ping the server.Based on the output of the show ip route command topology shown in the graphic,what is the cause of the failure?（）

A.IP routing is not enabled
B.A static route is configured incorrectly
C.The network has not fully converged
D.The FastEthernet interface on Coffee is disabled
E.The routing table on Coffee has not updated
F.The neighbor relationship table is not correctly updated

7.單項選擇題A router has two FastEthernet interfaces and needs to connect to four vlans in the local network.How can you accomplish this task,using the fewest physical interfaces and without decreasing network performance?（）

A.Add two more FastEthernet interfaces.
B.Add a second router to handle the vlan traffic.
C.Use a hub to connect the four vlans with a FastEthernet interface on router.
D.Implement a router-on-a-stick configuration.

8.單項選擇題

Refer to the exhibit a network administrator cannot establish a telnet session with the indicated router at is the cause of this failure?（）

A .A level 5 password is not set
B.The vty password is missing
C.The console password is missing
D.An ACL is blocking Telnet access

9.單項選擇題Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）

A.As numbers must be changed to match on all the routers.
B.Loopback interface must be configured so a DR is elected.
C.The no auto-summary command is needed on Router A and Router C.
D.Router B needs to have two network statements, one for each connected network.

10.單項選擇題

Refer to the exhibit. Which of these statements correctly describes the state of the switch once the boot process has been completed?（）

A.As FastEthernet0/12 will be the last to come up, it will not be blocked by STP.
B.Remote access management of this switch will not be possible without configuration change.
C.More VLANs will need to be created for this switch.
D.The switch will need a different IOS code in order to support VLANs and STP.