A.Add two more FastEthernet interfaces.
B.Add a second router to handle the vlan traffic.
C.Use a hub to connect the four vlans with a FastEthernet interface on router.
D.Implement a router-on-a-stick configuration.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit a network administrator cannot establish a telnet session with the indicated router at is the cause of this failure?（）
A .A level 5 password is not set
B.The vty password is missing
C.The console password is missing
D.An ACL is blocking Telnet access
A.As numbers must be changed to match on all the routers.
B.Loopback interface must be configured so a DR is elected.
C.The no auto-summary command is needed on Router A and Router C.
D.Router B needs to have two network statements, one for each connected network.
Refer to the exhibit. Which of these statements correctly describes the state of the switch once the boot process has been completed?（）
A.As FastEthernet0/12 will be the last to come up, it will not be blocked by STP.
B.Remote access management of this switch will not be possible without configuration change.
C.More VLANs will need to be created for this switch.
D.The switch will need a different IOS code in order to support VLANs and STP.
A.A dynamically learned MAC address is saved in the startup-configuration file.
B.A dynamically learned MAC address is saved in the running-configuration file.
C.A dynamically learned MAC address is saved in the VLAN database.
D.Statically configured MAC addresses are saved in the startup-configuration file if frames from that address are received.
E.Statically configured MAC addresses are saved in the running-configuration file if frames from that address are received.
A.SW1#show swithport port-security interface FastEthernet 0/12
B.SW1# show swithport port-secure interface FastEthernet 0/12
C.SW1# show port-secure interface FastEthernet 0/12
D.SW1#show running-config
E.SW1#show port-security interface FastEthernet 0/12
A.Administratively shut down the interfaces.
B.Physically secure the interfaces.
C.Configure a virtual terminal password and login process.
D.Enter an access list and apply it to the terminal interfaces using the access-class command.
E.Create an access list and apply it to the terminal interfaces using the access-group command.
A.access-list 10 permit ip 192.168.147.0 0.0.0.255.255
B.access-list 10 permit ip 192.168.149.0 0.0.0.255.255
C.access-list 10 permit ip 192.168.146.0 0.0.0.0.255
D.access-list 10 permit ip 192.168.146.0 0.0.1.255
E.access-list 10 permit ip 192.168.148.0 0.0.1.255
F.access-list 10 permit ip 192.168.146.0 255.255.255.0
A.access-list 50 deny 192.168.1.1 0.0.0.255
B.access-list 110 permit ip any any
C.access-list 2500 deny tcp any host 192.168.1.1 eq 22
D.access-list 101 deny tcp any host 192.168.1.1
A.you can apply multiple access lists with the same protocol or in different direction.
B.you can config one access list,per direction,per layer 3 protocol
C.you can place as many access lists as you want on any interface
D.you can apply only one access list on any interface
A.They are always present in the NAT table.
B.They allow connection to be initiated from the outside.
C.They can be configured with access lists, to allow two or more connections to be initiated from the outside.
D.They require no inside or outside interface markings because addresses are statically defined.
最新試題
Syslog was configured with a level 3 trap. Which 3 types of logs would be generated？（）
What is the default Syslog facility level?（）
What are the benefit of using Netflow?（）
Which one of these is a valid HSRP Virtual Mac Address?（）
What Cisco IOS feature can be enabled to pinpoint an application that is causing slow network performance?（）
What level will be trapped if the administrator executes the command ？（）
What are three values that must be the same within a sequence of packets for Netflow to consider them a network flow?（）
In a GLBP network, who is responsible for the arp request?（）
Which three statements about Syslog utilization are true?（）
What SNMP message alerts the manager to a condition on the network?（）