Refer to the exhibit. In the diagram， the switches are running IEEE 802.1s MST. Which ports are in the MST blocking state？（）
A. GE-1/2 and GE 2/1
B. GE-1/1 and GE-2/2
C. GE-3/2 and GE 4/1
D. no ports are in the blocking state
E. There is not enough information to determine which ports are in the blocking state.
您可能感興趣的試卷
你可能感興趣的試題
A.The originator of the TCN immediately floods this information through the network.
B.The TCN propagation is a two step process.
C.A TCN is generated and sent to the root bridge.
D.The root bridge must flood this information throughout the network.
Refer to the exhibit. Catalyst R is the root bridge for both VLAN 1 and VLAN 2.What is the easiest way to load-share traffic across both trunks and maintain redundancy in case a link fails，without using any type of EtherChannel link-bundling？（）
A. Increase the root bridge priority （increasing the numerical priority number） for VLAN 2 on Catalyst D so that port D2 becomes the root port on Catalyst D for VLAN 2.
B. Decrease the port priority on R2 for VLAN 2 on Catalyst R so that port D1 will be blocked for VLAN 2 and port D2 will remain blocked for VLAN 1.
C. Decrease the path cost on R2 on Catalyst R for VLAN 2 so that port D1 will be blocked for VLAN 2 and port D2 will remain blocked for VLAN 1.
D. Increase the root bridge priority （decreasing the numerical priority number） for VLAN 2 on Catalyst R so that R2 becomes the root port on Catalyst D for VLAN 2.
A.Loop guard only operates on interfaces that are considered point-to-point by the spanning tree.
B.Loop guard only operates on root ports.
C.Loop guard only operates on designated ports.
D.Loop guard only operates on edge ports.
A.It may allocate IP addresses from an unknown subnet to the users.
B.All multicast traffic can be sniffed by using the DHCP multicast capabilities.
C.The CPU utilization of the first hop router can be overloaded by exploiting DHCP relay open ports.
D.A potential man-in-the-middle attack can be used against the clients.
A. 1） lowest root bridge id，2）lowest sender bridge id，3）lowest port id，4）lowest root path cost
B. 1） lowest root path cost，2）lowest root bridge id，3）lowest sender bridge id，4）lowest sender port id
C. 1） lowest root bridge id，2）lowest sender bridge id，3）lowest root path cost 4）owest sender port id
D. 1） lowest root bridge id，2）lowest root path cost，3）lowest sender bridge id，4）lowest sender port id
最新試題
Which three protocols or applications should be placed in a class that is configured with WRED？（）
Which of these statements about penultimate hop popping are true？（）
The classic Spanning Tree Protocol （802.1 D 1998） uses which sequence of variables to determine thebest received BPDU？（）
Which multicast address is reserved for cisco-rp-discovery？（）
Which two are differences between IGMPv2 and IGMPv3 reports？（）
What is the correct command to set the router ID for an OSPFv3 process？（）
Which of these best describes the actions taken when a VTP message is received on a switch configuredwith the VTP mode "transparent"？（）
An expanding company is deploying leased lines between its main site and two remote sites. Thebandwidth of the leased lines is 128kb/s each，terminated on different serial interfaces on the main router.These links are used for combined VOIP and data traffic. The network administrator has implemented a VOIP solution to reduce costs，and has therefore reserved sufficient bandwidth in a low latency queue oneach interface for the VOIP traffic. Users now complain about bad voice quality although no drops areobserved in the low latency queue. What action will likely fix this problem？（）
In PIM-SM what control plane signaling must a multicast source perform before it begins to send multicasttraffic to a group？（）
Which message type is constructed and sent from an MSDP router to its MSDP peers when it receives a PIM register message knowing that the MSDP router is also configured as an RP for the PIM domain？（）