A.It is used only for directly connected subnets or aggregate routes
B.It can only be used with LDP.
C.It is only used when two or more labels are stacked.
D.It enables the Edge LSR to request a label pop operation from Its upstream neighbors
E.It is requested through TDP using a special label value that is also called the implicit-null value.
F.It is requested through LDP using a special label value that is also called the implicit-null value.
您可能感興趣的試卷
你可能感興趣的試題
A.prefixes received from any other BGP peer and prefixes locally originated via network statements or redistributed
B.all prefixes in its routing table
C.prefixes received from EBGP peers and prefixes locally originated via network statements or redistributed
D.prefixes received from EBGP peers and prefixes received from route reflectors
E.prefixes received from other IBGP peers， prefixes received from EBGP peers，and prefixes redistributedto BGP
F.prefixes received from other IBGP peers and prefixes received from route reflectors
A.dropper
B.classifier
C.marker
D.querier
E.meter
F.shaper
A.data marked with DSCP AF21，VOIP marked with DSCP EF
B.data marked with DSCP AF51，VOIP marked with DSCP EF
C.data marked with the DE-bit. VOIP marked with the CLP-bit
D.data marked with DSCP EF，VOIP marked with DSCP AF31
E.data marked with IP precedence 5，VOIP marked with DSCP EF
A.mark VOIP traffic with IP precedence 6 and configure only fair-queue’ on the links
B.configure the scheduler allocate 3000 1000 command to allow the OoS code to have enough CPU cycles
C.enable class-based traffic shaping on the VOIP traffic class
D.enable Layer 2 fragmentation and interleaving on the links
E.enable Frame Relay on the links and send voice and data on different Frame Relay PVCs
A.1） lowest root bridge id，2） lowest sender bridge id，3） lowest port id，4） lowest root path cost
B.1） lowest root path cost，2） lowest root bridge id，3） lowest sender bridge id，4） lowest sender port id
C.1） lowest root bridge id，2） lowest sender bridge id，3） lowest root path cost，4） lowest sender port id
D.1） lowest root bridge id，2） lowest root path cost，3） lowest sender bridge id，4） lowest sender port id
最新試題
Which two statements are true about RED？（）
Which three options are valid ways to filter routes from a BGP peer？（）
Which of these best describes the actions taken when a VTP message is received on a switch configuredwith the VTP mode "transparent"？（）
Two routers configured to run BGP have been connected to a firewall， one on the inside interface and one on the outside interface. BGP has been configured so the two routers should peer， including the correctBGP session endpoint addresses and the correct BGP session hop-count limit EBGP multihop. What is agood first test to see if BGP will work across the firewall？（）
How does an IPv6 router deal with a packet that is larger than the outgoing interface MTU？（）
Which two of these are used in the selection of a root bridge in a network utilizing Spanning Tree ProtocolIEEE 802.1 D？（）
Choose two commands that are required to enable multicast on a router， when it is known that thereceivers use a specific functionality of IGMPv3.（）
The classic Spanning Tree Protocol （802.1 D 1998） uses which sequence of variables to determine thebest received BPDU？（）
In Layer 2 topologies， spanning-tree failures can cause loops in the network. These unblocked loops cancause network failures because of excessive traffic. Which two Catalyst 6500 features can be used to limitexcessive traffic during spanning-tree loop conditions？（）
What is the correct command to set the router ID for an OSPFv3 process？（）