A. fibers are terminated incorrectly on a node
B. the channel number in the received K1 byte is not identical to the channel number transmitted in the K2 byte
C. the channel number in the received C1 byte is not identical to the channel number transmitted in the C2 byte
D. the channel number in the received C2 byte is not identical to the channel number transmitted in the C1 byte
E. the channel number in the received K2 byte is not identical to the channel number transmitted in the K1 byte
您可能感興趣的試卷
你可能感興趣的試題
A.255
B.512
C.1024
D.4096
A.line timing
B.loop timing
C.internal timing
D.through timing
E.external timing
A.2
B.3
C.4
D.20
E.22
F.24
A. VT circuits
B. STS circuits
C. VT tunnel circuits
D. 1:1 protection circuits
E. 1:N protection circuits
Click the Exhibit button. Given the information shown in the exhibit, when creating 2 DS1 circuits, how many STS ports are used on the VT1.5 matrix at Node 1 as VT circuits and how many are used after using VT tunnels?（）
A.2；0
B.3；2
C.3；5
D.4；0
E.6；0
F.6；2
A. Slot 2 and Slot 4
B. Slot 4 and Slot 6
C. Slots 5 or 13 only
D. Slot 16 and Slot 17
Click the Exhibit button. Which type of protection is shown in the exhibit?（）
A.1+0
B.1+1
C.1：1
D.1：N
A.0
B.1
C.2
D.3
E.4
A. signal fail, signal degrade, manual switch
B. signal degrade, signal fail, manual switch
C. protection lockout, manual switch, path AIS
D. forced switch, manual switch, signal degrade
E. protection lockout, manual switch, forced switch
A. Switch times would exceed 50 ms for an OC-3 BLSR ring.
B. An equal amount of working and protect bandwidth is required.
C. DCC bandwidth is not large enough to handle K1/K2 processing.
D. There is not enough bandwidth in an OC-3 ring to justify BLSR protection.
最新試題
What are two important considerations when using 2- or 4-channel 15216 OADMs?（） (Choose two.)
What are three relevant design considerations when using the 15216 EDFA? （）(Choose three.)
A 2.5 Gb/s (OC-48 or STM-16) optical signal with a dispersion tolerance of 1200 ps/nm goes through fiber with 18ps/nm*km of dispersion. How many 15216-DCU-350 equivalents are needed for enough compensation after traveling 100 km?（）
SONET Path Terminating Equipment (PTE) requires which three line codes to be supported for DS1 and DS3 circuits?（） (Choose three.)
UPSR protection switching is initiated by （）, while BLSR is initiated by （）.
Click the Exhibit button. Which type of multiplexer is shown in the exhibit?（）
Click the Exhibit button. Given the following parameters: transmitter output (min): -2 dBm receiver input (min): -28 dBm 15216 Mux and Demux loss: 4.5 dB 16 channels maximum In which sites shown in the exhibit could the 15216 EDFAs be placed to minimize the number of EDFAs needed?（）
A Channel ID mismatch occurs when （）.
If the power is 0 dBm, what is the power in mW?（）
Click the Exhibit button. What is the maximum allowable loss budget between the ONS 15216 Mux (left side) composite output and the ONS 15216 Demux (right side) composite input, with the optical values given in the exhibit? （）(Assume the worst case loss of 4.5 dB for 15216 200 GHz Mux/Demux and ignore power penalties or extra margin.)