You are trying to change the polling parameters used by the location manager via the Cisco WCS，and your request is being denied.
What is wrong？（）
A.Polling values can be changed only in the maintenance window.
B.Polling values can be changed only on the location server.
C.Your login does not have the correct permissions.
D.You must wait for the location server to become available.
您可能感興趣的試卷
你可能感興趣的試題
On a Cisco 1000 Series controller-based access point， the alarm LED is flashing red， but the otherLEDs are off.
What is this access point indicating？（）
A.Its IP address already exists.
B.It is operating normally.
C.It requires a code upgrade.
D.It has lost contact with the controller.
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network， but clients using PEAP are failing to log on.
Which situation would result in thistype ofproblem？（）
A.Posture validation has not been enabled
B.The AAA server is set to accept both MS-CHAP v2 and GTC for PEAP authentication
C.Clients and server are not using certificates
D.Clients have been set to validate the server identity
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter， the status LED and activity LED arealternating on and off.
What does this indicate？（）
A.The client card is not associated to the network.
B.The client card has awakened from power-save mode.
C.The driver has been installed incorrectly.
D.The client card has failed.
You have very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops. Youwant to increase the bandwidth available for the laptops by decreasing the bandwidth reserved forthe Cisco 7920 phones.
What is the lowest percentage of voice-allocated bandwidth you can select onthe WLAN controller？（）
A.55 percent
B.75 percent
C.40 percent
D.25 percent
Your customer has deployed a Cisco Wireless Location Appliance within its warehouseenvironment.
However， employees there have been experiencing problems when tracking objects using activeRFID tags.You use an access point scan to determine if the Location Appliance has been deployed correctly.
Making which change to warehouse deployment location services will most likely correct theproblem？（）
A.ensure channels are deployed such that they do not overlap
B.allow for the automatic containment of rogue access points
C.ensure each area is covered by a minimum of three access points
D.ensure a minimum RSSI value of -50
最新試題
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
The Cisco Wireless Location Appliance provides an audit trail for each device tracked for up to how many days？（）
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode？（）
Which of the following commands on the wireless interface of a Cisco 3845 Integrated Service Router allows the SSID to broadcast？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）