On a Cisco Aironet 1130AG Series standalone access point，the status LED is dark blue andblinking.
What does this indicate？（）
A.The access point is booting.
B.The internal radio has failed.
C.An access point buffer overflow is occurring.
D.A firmware upgrade is in progress.
您可能感興趣的試卷
你可能感興趣的試題
Your customer has deployed a Cisco Wireless Location Appliance within its warehouse environment. However，employees there have been experiencing problems when tracking objects using active RFIDtags. The RFID beacon rate is 10 seconds and you have discovered an issue with the RFID timeout value.
Where and how should the RFID value be changed？（）
A.on the Cisco WCS， to 95 seconds
B.on the Cisco WCS， to 45 seconds
C.on the wireless controller， to 95 seconds
D.on the wireless controller， to 45 seconds
Your customer has deployed a Cisco Wireless Location Appliance within its warehouse environment. However，employees there have been experiencing problems when tracking objects using active RFIDtags. The RFID tag data is not being collected.
On which device would you verify that RFIDs have beenenabled？（）
A.Cisco WCS
B.access point
C.location manager
D.wireless controller
You are trying to change the polling parameters used by the location manager via the Cisco WCS， and yourrequest is being denied.
What is wrong？（）
A.Your login does not have the correct permissions.
B.You must wait for the location server to become available.
C.Polling values can be changed only on the location server.
D.Polling values can be changed only in the maintenance window.
During the installation of the Cisco WCS version 4.0， an error occurs.
Where would you look for theinstallation log， in order to learn more about this error？（）
A.in the Cisco WCS installation directory
B.at the root of the installation drive
C.in the Cisco WCS\Logs directory
D.on the desktop of the server
A.Multiple controller-based access points will load-balance the containment task using fewer resources than a single access point.
B.Clients connected to the rogue access point may be out of the range of the controller-based access point providing containment.
C.Each controller-based access point can handle only a limited amount of clients connected to the rogue access points.
D.Clients connected to the rogue access point must be able to connect to the containment controller-based access point.
最新試題
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage？（）
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance？（）
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）
Which of the following commands on the wireless interface of a Cisco 3845 Integrated Service Router allows the SSID to broadcast？（）
You are using ADU and are authenticated and associated to an access point. However， you are unable to obtain an IP address.Which of these has caused this problem？（）
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
You review the Failed Attempts logs on an AAA server and find： "unknown network access servererror." Which failure could produce this error？（）