單項選擇題

You have configured a Cisco Catalyst switch to perform Layer 3 routing via an SVI and have 
assigned that interface to VLAN 20. To check the status of the SVI, you issue the show interfaces vlan 20 command at the CLI prompt. You see from the output display that the interface is in an "up/up" state. 
What must be true in an SVI configuration to bring the VLAN and line protocol up?()

A.The port must be physically connected to another Layer 3 device.
B.At least one port in VLAN 20 must be active.
C.The Layer 3 routing protocol must be operational and receiving routing updates from neighboring peer devices.
D.Because this is a virtual interface, the operational status will always be in an "up/up" state.


您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題What is true of standard access control lists when applied to an interface to control inbound or outbound traffic?()

A.The best match of the ACL entries will be used for granularity of control.
B.They use source IP information for matching operations.
C.They use source and destination IP information for matching operations.
D.They use source IP information along with protocol-type information for finer granularity of control.

2.單項選擇題When configuring a routed port on a Cisco multilayer switch, which of these is a required configuration task that you must perform to enable that port to function as a routed port? ()

A.Enable the switch to participate in routing updates from external devices with the router command in global configuration mode.
B.Enter the no switchport command to disable Layer 2 functionality at the interface level.
C.Each port participating in routing of Layer 3 packets must have an IP routing protocol assigned on aperinterface level.
D.Routing is enabled by default on a multilayer switch, so the port can become a Layer 3 routing interface by assigning the appropriate IP address and subnet information.

3.單項選擇題What benefit results from implementation of Layer 3 switching versus Layer 2 switching in a fully meshed campus network?()

A.ease of IP address assignment versus use of external routers
B.redundancy from trunking between distribution layer switches
C.provides first-hop redundancy to clients
D.allows inter-VLAN communication without requiring complexity of routing protocols

4.單項選擇題

You work as a network engineer for . You study the exhibit carefully.
 What best describes the Cisco IOS IP SLA command and output in the exhibit?()

A.verifies which operation types have been enabled for IP SLA source
B.verifies which operation types have been enabled for IP SLA responder
C.verifies which operation types are supported in software
D.verifies enabled operation types that are not running

5.單項選擇題

You work as a network engineer for. You study the exhibit carefully. Which of these is true based upon the output shown in the command?()
 Exhibit:

A.The port has security enabled and has shut down due to a security violation.
B.The port is operational and has reached its configured maximum allowed number of MAC addresses.
C.The port will allow access for 11 MAC addresses in addition to the 3 configured MAC addresses.
D.If the number of devices attempting to access the port exceeds 11, the port will shut down for 20 minutes, as configured.

最新試題

Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result?()

題型:單項選擇題

Which statement is correct about RSTP port roles?()

題型:單項選擇題

Which statement is correct about the use of the virtual interface on a WLC ?()

題型:單項選擇題

Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1? ()

題型:單項選擇題

Which router redundancy protocol cannot be configured for interface tracking?()

題型:單項選擇題

Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command, which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true?()

題型:單項選擇題

If G1/0/1 on DS1 is shutdown, what will be the current priority value of the Vlan105’s group on DS1 ?()

題型:單項選擇題

What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals?()

題型:單項選擇題

During routine maintenance, G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However, after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ? ()

題型:單項選擇題

Refer to the exhibit. What does the command channel-group 1 mode desirable do? () 

題型:單項選擇題