A. R 192.168.8.0/24 [120/1] via 192.168.2.2, 00:00:10, Serial0
B. R 192.168.11.0/24 [120/7] via 192.168.9.1, 00:00:03, Serial1
C. C 192.168.1.0/24 is directly connected, Ethernet0
D. R 192.168.5.0/24 [120/15] via 192.168.2.2, 00:00:10, Serial0
您可能感興趣的試卷
你可能感興趣的試題
A. It configures a router to send all packets out interface serial 0/0.
B. It configures a router to block routing updates from being sent out interface serial 0/0.
C. It configures a router as a firewall, blocking all unauthorized packets from exiting serial 0/0.
D. It configures a router to send all packets for unknown destination networks out interface serial 0/0.
E. It configures a router to drop all packets for which the destination network is unknown.
A. It is used to validate the sources of VTP advertisements sent between switches.
B. It is used to access the VTP server to make changes to the VTP configuration.
C. It allows two VTP servers to exist in the same domain, each configured with different passwords.
D. It is the password required when promoting a switch from VTP client mode to VTP server mode.
E. It is used to prevent a switch newly added to the network from sending incorrect VLAN information to the other switches in the domain.
A company is experiencing network delays. The network administrator discovers that a worker in a location far from the MDF has connected an old 10BASE-T switch with redundant links to the existing network.
How could this action be responsible for the impaired network performance?（）
A. Connecting a host to the old switch has created a broadcast storm.
B. The 10BASE-T switch forced the entire network to be reduced to 10 Mbps operation.
C. The old switch does not support VLANs, which has disabled the VLAN configuration of the entire the network.
D. The old switch does not support full-duplex operation, effectively forcing half-duplex operation throughout the network.
E. Spanning Tree Protocol has elected the old switch as the root bridge, creating inefficient data paths through the switched network.
A.DHCP
B.SMTP
C.SNMP
D.FTP
E.HTTP
F.TFTP
A. Denmark exchanges with Utah, Paris, and Berlin.
B. Utah exchanges only with Denmark.
C. Berlin exchanges with Denmark, Utah, and Paris.
D. Paris exchanges only with Denmark.
E. Denmark exchanges with only Paris and Utah.
最新試題
A network host is configured as follows: Host IP address: 192.168.16.183 Subnet mask: 255.255.255.224 Default gateway: 192.168.16.190 Which of the following statements describe the network to which this host is attached?（）
The following access list was applied outbound on he E0 interface connected to the 192.168.1.8/29 LAN:access-list 123 deny tcp 192.168.1.8 0.0.0.7 eq 20 anyaccess-list 123 deny tcp 192.168.1.9 0.0.0.7 eq 21 anyWhat effect will this access list have?（）
All WAN links is side the TestKing.com network use PPP with for authentication security. Which command will display the CHAP authentication process as it occurs between two routers in the network?（）
Which of the following describe router functions?（）
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? （）
Which command is used to display the placement and direction of an IP access control list on a router?（）
Which characteristics are representative of a link-state routing protocol?（）
You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）
Which statement describes the rule of split horizon?（）
Five minutes after issuing the show running-config command, a technician enters the command again and notices that several access list statements have been altered. Because of this, the technician believes that the router is being configured by an unknown person through Telnet. Before changing the router passwords, the technician would like to discover if anyone is connected to the router by Telnet and stop them from making further changes.Which commands will accomplish these options?（）