On your OSPF network, routers TK1 and TK2 belong to the same Ethernet network. However, they are unable to establish an adjacency over this link. While troubleshooting this problem, you issue the "show ip ospf interface Ethernet 0"command on each router. The output from these commands is displayed below:
What is the underlying cause of the routers failing to become adjacent?（）
A. The OSPF area is misconfigured.
B. The priority on TK2 should be set lower.
C. The cost on TK2 should be set lower.
D. The hello and dead timers are misconfigured.
E. You need to add a backup designated router to the network.
F. The OSPF process ID numbers do not match.
您可能感興趣的試卷
你可能感興趣的試題
While trying to diagnose a routing problem in the network, you issue RIP debugging as displayed below:
RtrA#debug ip rip
Rip protocol debugging is on
RtrA#
1d05h: RIP: sending v1 update to 255.255.255.255 via FastEthernet0/0 (172.16.1.1)
1d05h: RIP: build update entries
1d05h: network 10.0.0.0 metric 1
1d05h: network 192.168.1.0 metric 2
1d05h: RIP: sending v1 update to 255.255.255.255 via Serial0/0 (10.0.8.1)
1d05h: RIP: build update entries
1d05h: network 172.16.0.0 metric 1
RtrA#
1d05h: RIP: received v1 update from 10.0.15.2 on Serial0/0
1d05h: 192.168.1.0 in 1 hops
1d05h: 192.168.0 in 16 hops (inaccessible)
Based on the output of the above exhibit, which two of the following statements are true?（）
A. A ping to 10.0.15.2 will be successful.
B. RtrA has three interfaces that will take part in the RIP process.
C. There are at least two routers participating in the RIP process.
D. A ping to 192.168.168.2 will be successful.
A. TK1# show ip ospf interface
B. TK1# show ip ospf priority
C. TK1# show ospf neighbor detail
D. TK1# show ospf processes
E. TK1# show ospf neighbor state
A. Each end of the trunk line must be set to IEEE 802.1E encapsulation.
B. The VTP management domain name of both switches must be set the same.
C. All ports on both the switches must be set as access port.
D. One of the two switches must be configured as a VTP server.
E. A rollover cable is required to connect the two switches together.
F. A router must be used to forward VTP traffic between VLANs.
A. Ping
B. Tracert
C. Ipconfig
D. Show ip route
E. Winipcfg
F. Show interfaces
A. ping
B. tracert
C. ipconfig
D. show ip route
E. winipcfg
F. show interfaces
G. All of the above
最新試題
Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? （）
Given a subnet mask of 255.255.255.224, which of the following addresses can be assigned to network hosts?（）
Which of the following correctly describe steps in the OSI data encapsulation process?（）
Which of the following host addresses are member of networks that can be routed across the public Internet? （）
A Router with a BRI/T interface will be used for an ISDN Connection what other ISDN device is required to complete this connection? （）
A network host is configured as follows: Host IP address: 192.168.16.183 Subnet mask: 255.255.255.224 Default gateway: 192.168.16.190 Which of the following statements describe the network to which this host is attached?（）
TestKing.com has allocated the IP add 199.144.27.0 is its network, to provide flexibility for the LAN design, a subnet mask of 255.255.255.240 has been chosen. Which of the following address can be assigned to LAN on the resulting subnets.（）
New switches have been purchased for a network upgrade. The objective for the network design emphasizes efficient, error-free transport instead of fast transport.Which switching mode should be configured on the new switches to provide error-free transport to the network? （）
Which characteristics are representative of a link-state routing protocol?（）
Five minutes after issuing the show running-config command, a technician enters the command again and notices that several access list statements have been altered. Because of this, the technician believes that the router is being configured by an unknown person through Telnet. Before changing the router passwords, the technician would like to discover if anyone is connected to the router by Telnet and stop them from making further changes.Which commands will accomplish these options?（）