A.The interface you configured for AutoQoS is set to half-duplex
B.AutoQoS was configured on only one end of the link
C.The interface you configured for AutoQoS has no IP address
D.The interface’s bandwidth is not correctly configured
E.CEF is not enabled on the interface
F.You enabled AutoQoS on the interface but forgot to enable globally first
您可能感興趣的試卷
你可能感興趣的試題
A.Spanning Tree Protocol
B.Cabling
C.Frame forwarding
D.Packet forwarding
E.EtherChannel
F.Routing protocols
A.Building schematic
B.IGP community elements
C.Listing of interconnections
D.Physical topology diagram
E.Logical topology diagram
F.Inventory of network equipment
A.An error will result because a router cannot be configured with an EIGRP variance of 3 becausethe maximum variance number is 2
B.The successor route will end up in the routing table， and so will any route with a metric at mostthree times greater than the value of the successor’s metric
C.EIGRP will only advertise routes that are within three hops of the current router
D.The successor route will end up in the routing table， and so will any route with a metric at leastone third the value of the successor’s metric
E.The best three routes with equal cost paths will end up in the routing table
F.The successor route will be any route with three times the value of the advertised distance
A.Several processes can exist simultaneously
B.Requires direct connectivity from the backbone area to all other areas
C.Has the same packet types
D.Can support multiple subnets on a single link
E.Uses a hierarchical structure divided into areas
F.Adjacencies formed with neighbors
A.Filter unneeded BGP routes
B.Run BGP on a different platform that already has more memory
C.Upgrade the router memory
D.Increase the BGP update timer
E.Compress the BGP table
F.Use a default route instead of maintaining a full BGP table
最新試題
Refer to the exhibit. Which two statements about the AAA configuration are true？（）
Drag and drop question. The upper gives the MPLS functions， the bottom describes the planes.Drag the above items to the proper location at the below
Network Topology Exhibit：Configuration Exhibit：NET（config）# access-list 112 deny icmp any any echo logNET（config）# access-list 112 deny imp any any redirect logNET（config）# access-list 112 deny icmp any any mask-request logNET（config）# access-list 112 permit icmp any 10.1.1.0 0.0.0.255NET（config）# interface Fa0/1NET（config-if）# ip access-group 112 inYou work as a network administrator at networkTut.com， study the exhibit carefully. Theconfiguration has been applied to router NET to mitigate the threat of certain types of ICMPbasedattacks while allowing some ICMP traffic to the corporate LAN to work. However， the configurationis incorrect. On the basis of the information in the exhibit， which configuration option wouldcorrectly configure router NET？（）
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clicking the numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible.To gain access to either the topology or the SDK click on the button to left side of the screen thatcorresponds to the section you wish to access. When you have finished viewing the topology theSDK you can return to your questions by clicking on the Questions button to the left.Which defined peer IP address an local subnet belong to Crete？（）
IPSec VPN is a widely-acknowledged solution for enterprise network. Which three IPsec VPNstatements are true？（）
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）
Which three statements accurately describe IOS Firewall configurations？（）
Identify the recommended steps for worm attack mitigation by dragging and dropping them into thetarget area in the correct order.
In computer security， AAA stands for authentication， authorization and accounting. Which optionabout the AAA authentication enable default group radius enable command is correct？（）
Drag the correct statements about MPLS-based VPN on the left to the boxes on the right.（Not allstatements will be used）