Refer to the exhibit. Assume that Switch_A is active for the standby group and the standby devicehas only the default HSRP configuration. What conclusion is valid？（）
A.If port Fa1/1 on Switch_A goes down， the standby device will take over as active
B.If the current standby device were to have the higher priority value， it would take over the role ofactive for the HSRP group
C.If Switch_A had the highest prioritynumber， it would not take over as active router
D.If port Fa1/1 on Switch_A goes down， the new priority value for the switch would be 190
您可能感興趣的試卷
你可能感興趣的試題
Network topology exhibit：
In this network segment， the two routers on the network are configured for GLBP （Gateway LoadBalancing Protocol）. What can be said about this？（）
A.The hosts will have different default gateway IP addresses and different MAC addresses foreach rtouter
B.The default gateway address of each host should be set to the virtual IP address
C.The hosts will learn the proper default gateway IP address from Router R1
D.The default gateway address of each host should be set to the real IP address of the router
E.None of the other alternatives apply
Refer to the exhibit. Which three statements accurately describe this GLBP topology？（）
A.Router A is responsible for answering ARP requests sent to the virtual IP address.
B.If Router A becomes unavailable， Router B will forward packets sent to the virtual MAC addressof Router A
C.If another router were added to this GLBP group， there would be two backup AVGs
D.Router B is in GLBP listen state
E.Router A alternately responds to ARP requests with different virtual MAC addresses
F.Router B will transition from blocking state to forwarding state when it becomes the AVG
Routers R1 and R2 are configured for HSRP as shown below：
Router R1：
interface ethernet 0
ip address 20.6.2.1 255.255.255.0
standby 35 ip 20.6.2.21
standby 35 priority 100
interface ethernet 1
ip address 20.6.1.1.2 255.255.255.0
standby 34 ip 20.6.1.21
Router R2：
interface ethernet 0
ip address 20.6.2.2 255.255.255.0
standby 35 ip 20.6.2.21
interface ethernet 1
ip address 20.6.1.1.1 255.255.255.0
standby 34 ip 20.6.1.21
standby 34 priority 100
You have configured the routers R1 & R2 with HSRP. While debugging router R2 you notice veryfrequent HSRP group state transitions. What is the most likely cause of this？（）
A.physical layer issues
B.no spanning tree loops
C.use of non-default HSRP timers
D.failure to set the command standby 35 preempt
A.It can be used to block bulk encryption attacks
B.It can be used to protect against denial of service attacks
C.Traffic originating from the router is considered trusted， so it is not inspected
D.Based upon the custom firewall rules， an ACL entry is statically created and added to theexisting ACL permanently
E.Temporary ACL entries that allow selected traffic to pass are created and persist for theduration of the communication session
Refer to the exhibit. Host A has sent an ARP message to the default gateway IP address10.10.10.1. Which statement is true？（）
A.DSw1 will reply with the MAC address of the next AVF
B.DSw2 will reply with the MAC address of the next AVF
C.Because of the invalid timers that are configured， DSw1 will not reply
D.Because of the invalid timers that are configured， DSw2 will not reply
E.DSw1 will reply with the IP address of the next AVF
F.DSw2 will reply with the IP address of the next AVF
最新試題
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）
IPSec VPN is a widely-acknowledged solution for enterprise network. Which three IPsec VPNstatements are true？（）
Drag the DSL local loop topic on the left to the correct descriptions on the right.
Drag the protocols that are used to distribute MPLS labels from the above to the target area on thebelow.（Not all options will be used）
Drag the correct statements about MPLS-based VPN on the left to the boxes on the right.（Not allstatements will be used）
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define？（）
In computer security， AAA stands for authentication， authorization and accounting. Which optionabout the AAA authentication enable default group radius enable command is correct？（）
IPSec VPN is a widely-acknowledged solution for enterprise network. What are the four steps tosetup an IPsec VPN？（）
Which statement correctly describes IPsec VPN backup technology？（）
Drag the IPsec protocol description from the above to the correct protocol type on the below.（Notall descriptions will be used）Drag and Drop question， drag each item to its proper location.