What can be determined about the HSRP relationship from the displayed debug output？（）
A.Router 172.16.11.111 will be the active router because its HSRP priority is preferred over router172.16.11.112
B.The IP address 172.16.11.112 is the virtual HSRP router IP address
C.The nonpreempt feature is enabled on the 172.16.11.112 router
D.The IP address 172.16.11.111 is the virtual HSRP router IP address
E.Router 172.16.11.112 will be the active router because its HSRP priority is preferred over router172.16.11.111
F.The preempt feature is not enabled on the 172.16.11.111 router
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Based upon the debug output that is shown， which three statements aboutHSRP are true？（）
A.The router with IP address 172.16.11.112 is using default HSRP priority
B.The IP address 172.16.11.115 is the virtual HSRP IP address
C.The priority of the router with IP address 172.16.11.112 is preferred over the router with IPaddress 172.16.11.111
D.The router with IP address 172.16.11.111 haspreempt configured
E.The final active router is the router with IP address 172.16.11.111
F.The router with IP address 172.16.11.112 has nonpreempt configured
Refer to the exhibit. Which two statements are true about the output from the show standby vlan50 command？（）
A.The command standby 1 preempt was added to Catalyst_A
B.Catalyst_A is load sharing traffic in VLAN 50
C.Hosts using the default gateway address of 192.168.1.1 will have their traffic sent to192.168.1.11 even after Catalyst_A becomes available again
D.Hosts using the default gateway address of 192.168.1.2 will have their traffic sent toCatalyst_A
A.Hosts connected to the FastEthernet0/1 interface will not receive DHCP replies from the router
B.The first DHCP client to connect to the FastEthernet 0/1 interface will receive the IP address10.10.0.1
C.The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP address10.0.0.1
D.DHCP requests received on the FastEthernet 0/1 interface will be forwarded to 10.0.0.2
E.The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP address10.0.0.6
Refer to the exhibit. A network administrator has configured DHCP services on the router asshown. DHCP clients connected to the FastEthernet0/0 interface are working properly. DHCPclients connected to the FastEthernet0/1 interface are not receiving addresses. Which twostatements contain recommendations that will s
olve the problem？（）
A.The network shown in the output under the ip dhcp pool Central command should be changedto network 10.10.0.0 with a mask of 255.255.255.0
B.A second DHCP pool for network 10.10.0.0/24 should be configured
C.An ip dhcp excluded-address global configuration command for network 10.10.0.0/24 should beissued
D.The ip helper-address 10.0.0.1 command should be issued so that the address can be added tothe FastEthernet0/0 configuration
E.The ip helper-address 10.0.0.1 command should be issued so that the address can be added tothe FastEthernet0/1 configuration
A.The router will distribute IP addresses from pool 1 until its addresses are exhausted. Then therouter will begin distributing addresses from pool 2
B.The configuration is invalid because the DHCP options are global configuration commands
C.The configuration is incomplete until the DHCP pools are bound to the appropriate interface orinterfaces
D.The router will choose which pool to use based upon the interface the DHCP request wasreceived on
最新試題
A new router was configured with the following commands：The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
IPSec VPN is a widely-acknowledged solution for enterprise network. What are the four steps tosetup an IPsec VPN？（）
Drag the IOS commands from the left that would be used to implement a GRE tunnel using the10.1.1.0.30 network on interface serial 0/0 to the correct target area on the right.
Drag the protocols that are used to distribute MPLS labels from the above to the target area on thebelow.（Not all options will be used）
Which two encapsulation methods require that an 827 ADSL router be configured with a PPPusername and CHAP password？（）
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）
As a network technician， do you know what is a recommended practice for secure configurationmanagement？（）
Match the xDSL type on the above to the most appropriate implementation on the below.
Drag and drop each function on the above to the hybrid fiber-coaxial architecture component that itdescribes on the below.
Drag the IPsec protocol description from the above to the correct protocol type on the below.（Notall descriptions will be used）Drag and Drop question， drag each item to its proper location.