單項選擇題While troubleshooting a connectivity issue from a PC you obtain the following information: Local PC IP address: 10.0.0.35/24 Default Gateway: 10.0.0.1 Remote Sever: 10.5.75.250/24 You then conduct the following tests from the local PC: Ping 127.0.0.1 – Successful Ping 10.0.0.35 – Successful Ping 10.0.0.1 – Unsuccessful Ping 10.5.75.250 – Unsuccessful What is the underlying cause of this problem?()

A. A remote physical layer problem exists.
B. The host NIC is not functioning.
C. TCP/IP has not been correctly installed on the host.
D. A local physical layer problem exists.


您可能感興趣的試卷

你可能感興趣的試題

2.單項選擇題The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?()

A. The Gallant router has the wrong LMI type configured
B. Inverse ARP is providing the wrong PVC information to the Gallant router
C. The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command
D. The frame-relay map statement in the Attalla router for the PVC to Steele is not correct
E. The IP address on the serial interface of the Attalla router is configured incorrectly

3.單項選擇題A default Frame Relay WAN is classified as what type of physical network?()

A. point-to-point
B. broadcast multi-access
C. nonbroadcast multi-access
D. nonbroadcast multipoint
E. broadcast point-to-multipoint

4.單項選擇題The following configuration line was added to router R1 Access-list 101 permit ip 10.25.30.0 0.0.0.255 any What is the effect of this access list configuration?()

A. permit all packets matching the first three octets of the source address to all destinations
B. permit all packet matching the last octet of the destination address and accept all source addresses
C. permit all packet matching the host bits in the source address to all destinations
D. permit all packet from the third subnet of the network address to all destinations

5.單項選擇題The following access list below was applied outbound on the E0 interface connected to the 192.169.1.8/29 LAN: access-list 135 deny tcp 192.169.1.8 0.0.0.7 eq 20 any access-list 135 deny tcp 192.169.1.8 0.0.0.7 eq 21 any How will the above access lists affect traffic? ()

A. FTP traffic from 192.169.1.22 will be denied
B. No traffic, except for FTP traffic will be allowed to exit E0
C. FTP traffic from 192.169.1.9 to any host will be denied
D. All traffic exiting E0 will be denied
E. All FTP traffic to network 192.169.1.9/29 will be denied

最新試題

A network administrator is planning a network installation for a large organization.The design requires 100 separate subnetworks,so the company has acquired a Class B network address.What subnet mask will provide the 100 subnetworks required, if 500 usable host addresses are required per subnet?()

題型:?jiǎn)雾?xiàng)選擇題

After the show ip route command has been entered,the follwing routes are displayed.Which route will not be entered into the routing table of a neighboring router?()

題型:?jiǎn)雾?xiàng)選擇題

Which statement describes the rule of split horizon?()

題型:?jiǎn)雾?xiàng)選擇題

What is the subnetwork address for a host with the IP address 201.100.5.68/28?()

題型:?jiǎn)雾?xiàng)選擇題

An employee of ABC company has move to an office on a different floor. Although the administrator is able to telnet to all of the routers,the address of Switch F is needed in order to verify that the employee remains in the same VLAN.Which action could be used by the administrator to find the IP address of Switch F?()

題型:?jiǎn)雾?xiàng)選擇題

On which options are standard access list based?()

題型:?jiǎn)雾?xiàng)選擇題

A network administrator needs to configure a serial link between the main office and a remote location.The router at the remote office is a non-cisco router. How should the network administrator configure the serial interface of the main office router to make the connection?()

題型:?jiǎn)雾?xiàng)選擇題

What is the purpose of the cisco Vlan Trunking protocol?()

題型:?jiǎn)雾?xiàng)選擇題

At which layer of the OSI model dose PPP perform?()

題型:?jiǎn)雾?xiàng)選擇題

A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?()Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0

題型:?jiǎn)雾?xiàng)選擇題