A. B200
B. C210
C. B250
D. C260
E. C460
您可能感興趣的試卷
你可能感興趣的試題
A. 800 MHz
B. 900 MHz
C. 1066 MHz
D. 1333 MHz
E. 1666 MHz
A. Dual-rank DIMMs are not supported.
B. 16-GB DIMMs are too slow.
C. The largest DIMM an Intel 55xx or 56xx CPU can address is 32 GB
D. The memory bus would be too long.
E. The blade would run too hot.
A. Missing control VLAN in VSM configuration
B. Missing packet VLAN in VSM configuration
C. VSM has no network connection to vCenter
D. VSM extension key is not installed on vCenter
E. vCenter extension key is not installed on VSM
The network administrator is adding a new N1Kv to the vCenter， however， the administrator does not see the new switch under the networking tab of vCenter.
The administrator issues the following command on the VSM to troubleshoot：
VSM# show svs connections
connection VC：
ip address： 10.10.10.30
remote port： 80
protocol： vmware-vim https
certificatE. default
datacenter namE. DC1
DVS uuiD. 67 32 30 50 a6 d2 49 64-9e 1c 5f 49 e3 af 55 99
config status： Disabled
operational status： Disconnected sync status： -
version： -
When attempting to fix the issue， the following error is seen：
VSM-PRI-188# conf
VSM-PRI-188（config）# svs connection VC
VSM-PRI-188（config-svs-conn）# connect
ERROR： [VMWARE-VIM] Extension key was not registered before its use
What is the cause of the error？（）
A. Missing control VLAN in VSM configuration
B. Missing packet VLAN in VSM configuration
C. VSM has no network connection to vCenter
D. VSM extension key is not installed on vCenter
E. vCenter extension key is not installed on VSM
Given the following configuration：
port-profile type ethernet DATA-UPLINK
vmware port-group
switchport trunk allowed vlan 1-3967，4048-4093
channel-group auto mode on
no shutdown
state enabled
port-profile type ethernet MGMT-UPLINK
vmware port-group
switchport trunk allowed vlan 10-12
channel-group auto mode on
no shutdown
state enabled
VEMs are seen to be joining and then are lost from the Cisco VSM. How would you resolve this issue？（）
A. Remove second NIC from each port profile
B. Remove VEM from VSM （no vem X）， remove NICs， and reinsert
C. Ensure that VLANs on uplink profiles are not overlapping
D. Reinstall VEM
E. Issue the command "module vem X execute vemcmd set pinning module vsm 1"
A. Send monitored traffic to a VLAN
B. Send monitored traffic to a remote VEM over L2
C. Receive monitored traffic on a vEthernet interface
D. Send monitored traffic to an IP destination
A. Source and destination interface must be on the same host
B. Source and destination interfaces can be on different hosts
C. Destination vEthernet interface can be on a different VLAN than the source
D. Destination interface can be a physical port
E. Destination interface cannot be a physical port
Given a host with two NICs assigned to a N1k profile，which topologies are suitable for this type of configuration （）
port-profile type Ethernet name VM-Data
vmware port-group
switchport mode trunk
switchport allowed vlan 400-410
channel-group auto mode active
no shut
state enabled
A. Cisco UCS fabric interconnects
B. Pair of N5K’s in VPC
C. Standalone N5K
D. Pair of N5K’s in non-VPC
E. Cisco Catalyst 6000 Switch in VSS
A customer would like to monitor traffic that is being sent to a specific virtual machine named VM001 using SPAN. The customer has another virtual machine configured as a sniffer host called VM002. What configuration is required， and what other changes will need to be made？ （）
VSM-PRI-188# sh int vethernet 5
Vethernet5 is up
Port description is VM001， Network Adapter 2
HardwarE. Virtual， address： 0050.56b0.001e （bia 0050.56b0.001e）
Owner is VM "VM001"， adapter is Network Adapter 2
Active on module 5
VMware DVS port 484
Port-Profile is VM-vlan-10
Port mode is access
VSM-PRI-188# sh int vethernet 6
Vethernet6 is up
Port description is VM002， Network Adapter 1
HardwarE. Virtual， address： 0050.56b0.0020 （bia 0050.56b0.0020）
Owner is VM "VM002"， adapter is Network Adapter 1
Active on module 5
VMware DVS port 485
Port-Profile is VM-vlan-10
Port mode is access
A. Monitor session 1 type span Source interface veth5 both Destination interface veth6 No shut
B. monitor session 1 source vlan 10 destination interface veth6 no shut
C. monitor session 1 type er-span source interface vlan 10 destination ip 10.1.1.10 no shut
D. VM002 must be removed from the Nk1V
E. Move VM002 to Module 5
F. Restart the VEM on module 5
A. validates DHCP messages received from untrusted sources and filters out invalid response messages from DHCP servers
B. intercepts all ARP requests and responses on untrusted ports
C. builds and maintains the DHCP snooping binding database， which contains information about untrusted hosts with leased IP addresses
D. uses the DHCP snooping binding database to validate subsequent requests from untrusted hosts
E. limits IP traffic on an interface to only those sources that have an IP-MAC address binding table entry or static IP source entry
最新試題
In a Cisco Unified Computing System， What is the "designated receiver" port in end-host mode used for？（）
Given the following output： san-port-channel 12 is up Hardware is Fibre Channel Port WWN is 24：0c：00：0d：ec：d3：5c：00 Admin port mode is NP， trunk mode is on Port mode is NP Port vsan is 1 Speed is 8 Gbps Member[1] ： fc2/3 Member[2] ： fc2/4 What does "Speed is 8 Gbps" indicate？（）
When testing ICMP access to a functional load-balancing ACE VIP， it fails. What is the reason of this problem？ （）
What would be the cause for the following fault in UCS Manager？（） "ether VIF x / xxx down， reason： ENM source pinning failed"
Application Control Engine （ACE） can check the health of servers and server farms by configuring health probes （which are sometimes referred to as keepalives）. A probe can be one of many types. Which are valid ACE probes？ （）
Which statement is true regarding Backup tasks in Cisco UCS？（）
What is required for Cisco UCS C-Series rack server integration with Cisco UCS Manager？（）
Server load balancing （SLB） is the process of deciding to which server a load-balancing device should send a client request for service. Which predictors are supported on ACE in order to select the best server to fulfill a client request？ （）
Which is true when describing a connection replication in Cisco ACE？（）
What interface is created when an FC Port Channel is created on a Cisco Unified Computing System？（）