Refer to the exhibit.
Given this FCoE topology， host VFC interface and FC storage are in the same VSAN （VSAN 10）.The VSAN is in the allow list for both ISLs. Both ISLs are up at 4 GB.
Which command can be issued on the N5K command line to confirm that SCSI traffic from the host to the storage will flow across both links， as opposed to using only one link？（）
A. show fspf traffic vsan 10
B. show vsan 10
C. show trunk protocol
D. show fcroute unicast vsan 10
您可能感興趣的試卷
你可能感興趣的試題
A. port security
B. fabric binding
C. IVR
D. port tracking
E. FICON
A. Two peer devices： the vPC peers of which one is primary and one is secondary and are part of a vPC domain.
B. A Layer 3 Gigabit Ethernet link called peer-keepalive link to resolve dual-active scenarios
C. A redundant 10 Gigabit Ethernet PortChannel called a peer link to carry traffic from one system to the other when needed
D. vPC member ports forming the PortChannel
E. A dot1q trunk between the vPC peers
F. A management port that can be used as peer-keepalive link to resolve dual-active scenarios.
A. The Ethanalyzer captures control-plane traffic， while SPAN captures all traffic.
B. The Ethanalyzer captures all traffic including control-plane traffic， while SPAN captures only the control-plane traffic.
C. The Ethanalyzer captures only data traffic， while SPAN captures all traffic.
D. The Ethanalyzer captures only control traffic， while SPAN captures data traffic.
A. show memory detailed
B. show process cpu sorted
C. show system resources
D. show hardware capacity
A. show interface priority-flow-control
B. show interface queuing
C. show queuing interface
D. show policy-map system type queuing
E. show policy-map interface ethernet
Nexus7000# config t
Nexus700（config）# interface ethernet 2/11
Nexus700（config-if）# switchport mode private-vlan host
Nexus700（config-if）# switchport private-vlan host-association 14 50
Nexus700（config-if）# exit
Nexus700（config）#
What will this command sequence achieve？（）
A. associate interface E2/11 to community VLANs 14 and 50
B. associate interface E2/11 to secondary VLANs 14 and 50
C. associate interface E2/11 to primary VLAN 50 and secondary VLAN 14
D. associate interface E2/11 to primary VLAN 14 and secondary VLAN 50
A. Port priority value can be configured between 1 and 65535.
B. A higher port priority value means a higher priority of LACP.
C. Port priority can be configured so that specific links can be chosen as active links rather than the hot standby links within the port channel.
D. LACP uses the port priority with the port number to form the port identifier.
E. LACP Port priority default value should always be changed
A. Cisco AV-pair
B. TACACS+ or RADIUS ack frame role attribute
C. DH-CHAP challenge attribute
D. privilege level attribute
A. Graceful consistency check is enabled by default.
B. When graceful consistency check is enabled， only the links on the secondary peer device are suspended.
C. Graceful consistency check is disabled by default， so to enable this feature， use graceful consistency-check command under VPC domain configuration mode.
D. When graceful consistency check is enabled， only the inconsistent VLANs on the secondary peer device are suspended.
A. A single VACL can be shared across two or more VDCs.
B. Use of VACLs requires no special license to be installed.
C. VACLs make use of IP or MAC ACLs.
D. Only options drop and forward are permitted.
最新試題
Which is true when describing a connection replication in Cisco ACE？（）
An administrator creates a vNIC and assigns it to Fabric A with the fabric failover feature enabled. Which statement is true？（）
A Cisco UCS fabric interconnect in end-host mode learns MAC addresses on which port types？（）
In a Cisco Unified Computing System， What is the "designated receiver" port in end-host mode used for？（）
On a Cisco Unified Computing System （UCS）， which two statements regarding Ethanalyzer are true？（）
Server load balancing （SLB） is the process of deciding to which server a load-balancing device should send a client request for service. Which predictors are supported on ACE in order to select the best server to fulfill a client request？ （）
What is the purpose of this command in a Cisco Application Control Engine？（） switch/Admin# show np 1 me-stats "-F0 v"
Application Control Engine （ACE） can check the health of servers and server farms by configuring health probes （which are sometimes referred to as keepalives）. A probe can be one of many types. Which are valid ACE probes？ （）
Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager？ （）
What is required for Cisco UCS C-Series rack server integration with Cisco UCS Manager？（）