哪個設備會被選為根橋？
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. When applying this policy map on the tunnel1 interface， you see packet loss for the TCP class starting at around 100000 b/s， instead of the configured 150000 b/s. What is the most likely cause of the discrepancy？（）
A.The violate-action command should not be configured.
B.The current configuration of the load-interval command on the tunnel interface is preventing proper policing calculations.
C.The burst size is too low.
D.Policing on tunnel interfaces is not supported.
E.The CIR keyword is missing in the policer.
Refer to exhibits 1 and 2. In exhibit 1，all users on the LAN segment use router A as the active HSRP router. Router B is the standby router for the HSRP. In exhibit 2，the network management team reported that there is no utilization on the WAN link B. To solve this problem，you decide to change the logical topology of your LAN，but you are not sure about what changes must be made. You must manage HSRP or change it to another protocol in order to provide the most scalable design，automatic redundancy，and load balancing. Which one of these actions would be the best choice？（）
A.Use MHSRP，with three users using router A as the default gateway and three users using router B as the default gateway.
B.Keep HSRP and activate PBR to redirect half of the traffic to the other WAN link.
C.Use the backup interface on the WAN link B to provide load balancing for all users.
D.Use GLBP instead，because it provides you with up to three MAC addresses for the same default gateway virtual IP address.
E.Use GLBP instead，because it provides you with up to four MAC addresses for the same default gateway virtual IP address.
Refer to the exhibit. When applying this hierarchical policy map on the on the tunnel1 interface， you measure high jitter for traffic going through class 1234. What is the most likely cause of this jitter？（）
A.The configuration of a hierarchical policy map on a tunnel interface is not supported.
B.Class 5555 and class 5554 are both taking up 100% of the bandwidth， leaving nothing for class 1234.
C.The burst size for the traffic shaping is wrongly configured to 15000； this would require an interface capable of sending at 150Mb/s.
D.The burst size for the traffic shaping has been wrongly configured； it should be set as low as possible.
E.The burst size for the traffic shaping has been wrongly configured； it should be set as high as possible.
最新試題
The Frame Relay network in the diagram is not functioning properly.What is the cause of the problem?（）
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2.The routers cannot establish an adjacency relationship on their common Ethernet link.The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2.Based on the information in the graphic,what is the cause of this problem?（）
How should arouter that is being used in a Frame Relay network be configured to avoid split horizon issues from preventing routing updates?（）
As a CCNA candidate,you must have a firm understanding of the IPv6 address structure.Refer to IPv6 address,could you tell me how many bits are included in each filed?（）
The following configuration line was added to router R1 Access-list 101 permit ip 10.25.30.00.0.0.255 any What is the effect of this access list configuration?（）
what is the advantage of policing opposite to shaping？
What is the next state of initial in spanning-tree protocol？
QoS機制中的分類，采用ip數據包中的哪個字段？
當將多個交換機加入到MST region當中會發生什么（what happen）？
什么問題導致SERVER VTP密碼跟替他交換機VTP密碼不匹配？