A.provides common view of entire topology
B.exchanges routing tables with neighbors
C.calculates shortest path
D.utilizes event-triggered updates
E.utilizes frequent periodic updates
您可能感興趣的試卷
你可能感興趣的試題
A.120
B.100
C.90
D.110
Refer to the exhibit. A network administrator configures a new router and enters the copy startup-config running-config on the router. The network administrator powers down the router and sets it up at a remote location. When the router starts, it enter the system configuration dialog as shown. What is the caust of the problem?（）
A.The network administrator faled to save the configuration.
B.The configuration register is set to 0x2100.
C.The boot system flash command is missing from the configuration.
D.The configuraiton register is set to 0x2102.
E.The router is configured with the boot system startup command.
A.It supports VLSM.
B.It is used to route between autonomous systems.
C.It confines network instability to one area of the network.
D.It increases routing overhead on the network.
E.It allows extensive control of routing updates.
F.It is simpler to configure than RIP v2.
A.hello packets
B.SAP messages sent by other routers
C.LSAs from other routers
D.beacons received on point-to-point links
E.routing tables received from other link-state routers
F.TTL packets from designated routers
A.traceroute address
B.tracert address
C.ssh address
D.telnet address
A.show reload
B.show boot
C.show running-config
D.show version
A.the amount of available ROM
B.the amount of available flash and RAM memory
C.the version of the bootstrap software present on the router
D.show version
E.show processes
F.show running-config
Refer to the graphic. A static route to the 10.5.6.0/24 network is to be configured on the HFD router. Which commands will accomplish this? （）
A.HFD（config）#iproute10.5.6.00.0.0.255fa0/0
B.HFD（config）#iproute10.5.6.00.0.0.25510.5.4.6
C.HFD（config）#iproute10.5.6.0255.255.255.0fa0/0
D.HFD（config）#iproute10.5.6.0255.255.255.010.5.4.6
E.HFD（config）#iproute10.5.4.60.0.0.25510.5.6.0
F.HFD（config）#iproute10.5.4.6255.255.255.010.5.6.0
Refer to the exhibit. A network associate has configured OSPF with the command:
City(config-router)# network 192.168.12.64 0.0.0.63 area 0
After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? （）
A.FastEthernet0 /0
B.FastEthernet0 /1
C.Serial0/0
D.Serial0/1.102
E.Serial0/1.103
F.Serial0/1.104
A.link bandwidth
B.hop count
C.link cost
D.administrative distance
E.link delay
最新試題
What command visualizes the general NetFlow data on the command line?（）
What are three values that must be the same within a sequence of packets for Netflow to consider them a network flow?（）
What Netflow component can be applied to an interface to track IPv4 traffic?（）
Which three statements about the features of SNMPv2 and SNMPv3 are true?（）
Which three are the components of SNMP? （）
Refer to the exhibit.If the router Cisco returns the given output and has not had its router ID set manually, what value will OSPF use as its router ID?（）
What are three factors a network administrator must consider before implementing Netflow in the network?（）
What level will be trapped if the administrator executes the command ？（）
Which three statements about Syslog utilization are true?（）
In a GLBP network, who is responsible for the arp request?（）