單項選擇題At which layer of the OSI model is RSTP used to prevent loops?（）

A.data link
B.network
C.physical
D.transport


您可能感興趣的試卷

你可能感興趣的試題

1.多項選擇題Which three statements about RSTP are true?（）

A.RSTP significantly reduces topology reconverging time after a link failure.
B.RSTP expends the STP port roles by adding the alternate and backup roles.
C.RSTP port satates are blocking,discarding,learing,or forwarding.
D.RSTP also uses the STP proprsal-agreement sequence.
E.RSTP use the same timer-baseed process as STP on point-to-point links.
F.RSTP provides a faster transition to the forwarding state on point-to-point links than STP does.

2.單項選擇題

Refer to the exhibit A frame on vlan 1 on switch s1 is sent to switch s2 when the frame is received on vlan 2,what causes this behavior?（）

A.trunk mode mismatches
B.vlans that do not correspond to a unique IP subnet
C.native vlan mismatches
D.allowing only vlan 2 on the destination.

3.多項選擇題

Refer to the topology shown in the exhibit. Which ports will be STP designated ports if all the links are operating at the same bandwidth? （）

A.Switch A - Fa0/0
B.Switch A - Fa0/1
C.Switch B - Fa0/0
D.Switch B - Fa0/1
E.Switch C - Fa0/0
F.Switch C - Fa0/1

4.單項選擇題Which statement about vlan operation on cisco catalyst switches is true?（）

A.when a packet is received from an 802.1Q trunk,the vlan id can be determined from the source MAC address table.
B.unkown unicast frames are retransmitted only to the ports that belong to the same vlan
C.ports between switches should be configured in access mode so that vlans can span across the ports
D.broadcast and multicast frames are retransmitted to ports that are configured on different vlan.

5.單項選擇題assuming the default switch configuration which vlan range can be added modified and removed on a cisco switch?（）

A.2 through 1001
B.1 through 1001
C.1 through 1002
D.2 through 1005

6.多項選擇題Which two link protocols are used to carry multiple VLANs over a single link? （）

A.VTP
B.802.1q
C.IGP
D.ISL
E.802.3u

7.單項選擇題

Refer to the exhibit. Why has this switch not been elected the root bridge for VLAN1?（）

A.It has more than one interface that is connected to the root network segment.
B.It is running RSTP while the elected root bridge is running 802.1d spanning tree.
C.It has a higher MAC address than the elected root bridge.
D.It has a higher bridge ID than the elected root bridge.

8.單項選擇題Why will a switch never learn a broadcast address?（）

A.Broadcast frames are never sent to swiches.
B.Broadcast addresses use an incorrect format for the switching table.
C.A broadcast address will never be the source address of a frame.
D.Broadcasts only use network layer addressing.
E.A broadcast frame is never forwarded by a switch.

9.單項選擇題

Refer to the exhibit. Given the output shown from this Cisco Catalyst 2950, what is the most likely reason that interface FastEthernet 0/10 is not the root port for VLAN 2?（）

A.This switch has more than one interface connected to the root network segment in VLAN 2.
B.This switch is running RSTP while the elected designated switch is running 802.1d Spanning Tree.
C.This switch interface has a higher path cost to the root bridge than another in the topology.
D.This switch has a lower bridge ID for VLAN 2 than the elected designated switch.

10.單項選擇題

Refer to the exhibit.All switch ports are assigned to the correct VLANs, but none of the hosts connected to SwitchA can communicate with hosts in the same VLAN connected to SwitchB. Based on the output shown, what is the most likely problem?（）

A.The access link needs to be configured in multiple VLANs.
B.The link between the switches is configured in the wrong VLAN.
C.The link between the switches needs to be configured as a trunk.
D.VTP is not configured to carry VLAN information between the switches.
E.Switch IP addresses must be configured in order for traffic to be forwarded between the switches