A.point-to-point and multiaccess
B.point-to-multipoint and multiaccess
C.point-to-point and point-to-multipoint
D.nonbroadcast and broadcast multipoint
E.nonbroadcast and broadcast multiaccess
您可能感興趣的試卷
你可能感興趣的試題
A.to prevent unauthorized Telnet access to a switch port
B.to limit the number of Layer 2 broadcasts on a particular switch port
C.to prevent unauthorized hosts from accessing the LAN
D.to protect the IP and MAC address of the switch and associated ports
E.to block unauthorized access to the switch management interfaces over common TCP ports
A.permit all packets matching the first three octets of the source address to all destinations
B.permit all packets matching the last octet of the destination address and accept all source addresses
C.permit all packets from the third subnet of the network address to all destinations
D.permit all packets matching the host bits in the source address to all destinations
E.permit all packets to destinations matching the first three octets in the destination address
A.Establish a direct link from the switch to all other switches in the network.
B.Assign the switch a higher MAC address than the other switches in the network have.
C.Configure the switch so that it has a lower priority than other switches in the network.
D.Configure the switch for full-duplex operation and configure the other switches for half-duplex operation.
E.Connect the switch directly to the MDF router， which will force the switch to assume the role of root bridge.
A.It is used to validate the sources of VTP advertisements sent between switches.
B.It is used to access the VTP server to make changes to the VTP configuration.
C.It allows two VTP servers to exist in the same domain， each configured with different passwords.
D.It is the password required when promoting a switch from VTP client mode to VTP server mode.
E.It is used to prevent a switch newly added to the network from sending incorrect VLAN information to the other switches in the domain.
A.to verify the type of cable interconnecting two devices
B.to determine the status of network services on a remote device
C.to obtain VLAN information from directly connected switches
D.to verify Layer 2 connectivity between two devices when Layer 3 fails
E.to obtain the IP address of a connected device in order to telnet to the device
F.to determine the status of the routing protocols between directly connected routers
最新試題
Which cisco ios command can help to determine the timing of various debug events,relative to each other,when you are debugging a complicated router issue?（）
How are VTP advertisements delivered to switches across the network?（）
If all OSPF routers in a single area are configured with the same priority value,what value dose a router use for the ODPF router ID in the absence of a loopback interface?（）
On which options are standard access list based?（）
Which command displays the CHAP authentication process as it occurs between two routers?（）
An employee of ABC company has move to an office on a different floor. Although the administrator is able to telnet to all of the routers,the address of Switch F is needed in order to verify that the employee remains in the same VLAN.Which action could be used by the administrator to find the IP address of Switch F?（）
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
The network administrator cannot to switch 1 over a telnet session,although the hosts attached to switch 1 can ping the interface Fa0/0 of the router.Given the information in the graphic and assuming that the router and switch2 are configured properly,which of the following commands should be issued on switch 1 to correct this problem?（）
A router receives information about network 192.168.10.0/24 from multiple sources.What will the router consider the most reliable information about the path to that network?（）
Which statement describes the rule of split horizon?（）